manualshive.com logo in svg

Piscine Solide IMPACT OCEANIA, Installation Manual, Page: 52 / 64

Share
Download
Piscine Solide IMPACT OCEANIA Installation Manual Download Page 52

No Diving or Jumping.  Observe all Safety Rules

4-2

GENERAL INSTRUCTIONS - BRACELESS OVAL POOLS

ASSEMBLING THE POOL FRAME

A. INSTALLATION OF THE UPRIGHTS - Round Section

Section

4

1. Install the uprights - round section

 
a.  Insert an upright into the bottom plate. The upright 

is properly positioned when the bottom plate is 
inserted into the notch at the lower end of the 
upright. 

(Image 15)

b.  Slant the upright slightly towards the interior 

of the pool while inserting it. Ensure that the 
upright is correctly inserted into the bottom plate.        

(Images 6 to 8)

c.  Proceed with the installation of all the uprights.
 

Important Note:

Use the ridges in the pool wall to make sure the upright 
column is straight up and down.

Important Note:

Ensure to leave a gap between the two bottom rails.

See Diagram:

Please refer to your pool’s footprint (Section 1, pg11) for gap 
measurement.

5

6

7

8

Summary of Contents for IMPACT OCEANIA

































































Reviews:

No comments