Piper Arrow IV Maintenance Manual Download | Manualshive

Page: 469 / 752

background image

3. Gyro Filters:

A. Gyro filters must be serviced on a scheduled basis, not to exceed 100 hours, or sooner as condition

indicates.

B. The system installation employs a large central filter and differential vacuum gauge that

continuously monitors the filter condition while indicating vacuum readings.

—NOTE—

The latest systems which employ a central filter in combination
with a differential vacuum gauge will indicate a decline in panel
gauge reading when the filter becomes clogged and vacuum
declines below the recommended value. The filters should be
replaced when gauge reading declines below the recommended
value; do not adjust regulator.

4. Vacuum Regulator:

A. The vacuum regulating valve seldom needs replacement. Symptoms that suggest replacement are:

(1) Chatter as indicated by rapid fluctuation of the vacuum gauge needle or an audible sound.
(2) Non-repeatability of the vacuum gauge reading when the panel gauge is not suspect or has

been checked against a known test gauge (cruise RPM only).

B. All modes of regulator malfunction tend to increase the vacuum power applied to the gyros. Thus,

although excess vacuum is applied, a loss of vacuum does not occur.

C. The gyros themselves act as a limiting device to keep the vacuum power applied from exceeding

safe levels.

—NOTE—

If the panel gauge has been checked and found OK and the
vacuum gauge reading does not repeat within the range of 4.8 to
5.2 inches of mercury, then the regulating valve should be
changed. Observe the usual precautions for maintaining system
cleanliness to avoid premature pump service.

VACUUM PUMP.

The vacuum pump is of the rotary vane, positive displacement type. This unit consists essentially of an

aluminum housing containing a tempered sleeve in which an offset rotor, with moving blades is incorporated.
This assembly is driven by means of a coupling mated to the engine driven gear assembly. The pump is
mounted on the accessory section of the engine.

37-10-02

Page 37-04

Revised: August 18, 1980

2H22

PIPER AIRCRAFT

PA-28RT-201 / 201T

MAINTENANCE MANUAL

«
...
467
468
469
470
471
...
»

Summary of Contents for Arrow IV

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Arrow IV

Brand: SOL paragliders Pages: 26

Brand: AUTO GYRO Pages: 147

Brand: U-Turn Pages: 33

Brand: U-Turn Pages: 46

Brand: TOMAHAWK SPORT Pages: 36

Brand: STEMME Pages: 290

Beechcraft Bonanza V35

Brand: Beech Pages: 362

Brand: SKY PARAGLIDERS Pages: 21

Brand: MAC PARA Pages: 40

2018 DOUBLE AGENT

Brand: Cabrinha Pages: 10

Brand: Ozone Pages: 8

Brand: X-dream Fly Pages: 32

Brand: Schleicher Pages: 13

Ka8 B/C Rhonsegler

Brand: Schleicher Pages: 43

Brand: Eiri KY Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands