Piper Aircraft Corporation Malibu Mirage PA-46-350P Airplane Maintenance Manual Download

Page: 833 / 1956

PAGE 7

Feb 28/07

4F7

32-40-00

PIPER AIRCRAFT, INC.

PA-46-350P, MALIBU MIRAGE

MAINTENANCE MANUAL

(6)

Remove the two nuts, bolts, and washers holding cylinder assembly to rudder bar.

(7)

Remove toe brake and cylinder assembly from airplane.

Disassembly, Repair, and Installation

(1)

Remove end fitting from cylinder housing.

(2)

Slide entire rod and ring assembly with attached piston out of cylinder housing.

NOTE: Repairs to the rod and ring assembly and piston are limited to polishing small

scratches and burrs, and replacement of parts.

(3)

Clean cylinder bore, rod and ring assembly, and piston with dry-type solvent.

(4)

To replace any of the component parts shown in the parts catalog, remove retaining ring. All
parts will slide off rod and ring assembly.

(5)

Soak end fitting O-rings (one internal, one external) and piston O-ring in hydraulic fluid. Coat
with fluid compatible gel.

(6)

Install power spring on rod and ring assembly.

Brake System Installation

Figure 5

Summary of Contents for Malibu Mirage PA-46-350P





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Malibu Mirage PA-46-350P

Reviews:

Related manuals for Malibu Mirage PA-46-350P

Brands by name

Popular brands

Piper Aircraft Corporation Malibu Mirage PA-46-350P, Airplane Maintenance Manual

Search results

Summary of Contents for Malibu Mirage PA-46-350P

Reviews:

Related manuals for Malibu Mirage PA-46-350P

Brands by name

Popular brands