Connecting your equipment
8
En
• Surround and surround back speakers should be
positioned 60 cm to 90 cm higher than your ears and
titled slight downward. Make sure the speakers don’t face
each other. For DVD-Audio, the speakers should be more
directly behind the listener than for home theater
playback.
• Try not to place the surround speakers farther away from
the listening position than the front and center speakers.
Doing so can weaken the surround sound effect.
• Place the left and right front height speakers at least one
meter directly above the left and right front speakers.
• If you’re going to place speakers around your CRT TV, use
shielded speakers or place the speakers at a sufficient
distance from your CRT TV.
• The subwoofer can be placed on the floor. Ideally, the
other speakers should be at about ear-level when you’re
listening to them. Putting the speakers on the floor
(except the subwoofer), or mounting them very high on a
wall is not recommended.
• When not connecting a subwoofer, connect speakers
with low frequency reproduction capabilities to the front
channel. (The subwoofer’s low frequency component is
played from the front speakers, so the speakers could be
damaged.)
•
After connecting, be sure to conduct the Auto
MCACC (speaker environment setting) procedure.
See
Automatically setting up for surround sound (MCACC)
on page 19.
CAUTION
• Make sure that all speakers are securely installed. This
not only improves sound quality, but also reduces the risk
of damage or injury resulting from speakers being
knocked over or falling in the event of external shocks
such as earthquakes.
Connecting the speakers
The receiver will work with just two stereo speakers (the front
speakers in the diagram) but using at least three speakers is
recommended, and a complete setup is best for surround
sound.
Make sure you connect the speaker on the right to the right
(
R
) terminal and the speaker on the left to the left (
L
) terminal.
Also make sure the positive and negative (
+
/
–
) terminals on
the receiver match those on the speakers.
You can use speakers with a normal impedance between 6
Ω
and 16
Ω
.
Important
•
VSX-821 only:
Note that only the front speakers are set to a
value between 12
Ω
and 16
Ω
if you select
SP
AB
in
Switching the speaker terminal
on page 10.
Be sure to complete all connections before connecting this unit
to the AC power source.
Bare wire connections
1
Twist exposed wire strands together.
2
Loosen terminal and insert exposed wire.
3
Tighten terminal.
Connect the wires to the B Speakers terminals of the VSX-826
as shown below:
1
Twist exposed wire strands together.
2
Push open the tabs and insert exposed wire.
3
Release the tabs.
CAUTION
• These speaker terminals carry
HAZARDOUS LIVE
voltage
. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
• Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker terminal. If
any of the bare speaker wire touches the back panel it
may cause the power to cut off as a safety measure.
Connect the surround back or front height
speakers (In case of VSX-826)
The Speaker System setting must be set if the above
connections are performed. Select
Surr.Back
if the surround
back speaker is connected and
Height
if the front height
speaker is connected (If neither the surround back speaker
nor the front height speaker is connected, either setting will
suffice) (see
The Speaker System setting (VSX-826 only)
on
Operating Instructions in CD-ROM).
• When using only one surround back speaker, connect it
to the
SURROUND BACK L (Single)
terminals.
Connect the surround back or front height
speakers (In case of VSX-821)
Connect the
PRE OUT SURR BACK/FRONT HEIGHT
outputs
of the unit and additional amplifier to add a surround back or
front height speaker.
The Pre Out setting must be set if the above connections are
performed. Select
SURR.BACK
if the surround back speaker
is connected and
HEIGHT
if the front height speaker is
connected (If neither the surround back speaker nor the front
height speaker is connected, either setting will suffice) (see
The Pre Out Setting (VSX-821 only)
on Operating Instructions
in CD-ROM).
• You can use the additional amplifier on the surround back
channel pre-outs for a single speaker as well. In this case
plug the amplifier into the left (
L (Single)
) terminal only.
1
2
3
10 mm
1
2
3
10 mm
VSX-821_826_SYXCN_QSG_En.book 8 ページ ２０１１年３月１日 火曜日 午前９時５０分
