Additional information
7
7
35
Resetting the main unit
Use this procedure to reset all the receiver’s settings to the
factory default. Use the front panel controls to do this.
1
Switch the receiver into standby.
2
While holding down
BAND
, press and hold
Í
STANDBY/ON
for about two seconds.
3
When you see RESET? appear in the display, press
AUTO SURROUND/STREAM DIRECT
.
OK?
shows in the display.
4
Press
ALC/STANDARD SURR
to confirm.
OK
appears in the display to indicate that the receiver
has been reset to the factory default settings.
Cleaning the unit
•
Use a polishing cloth or dry cloth to wipe off dust and dirt.
•
When the surface is dirty, wipe with a soft cloth dipped in
some neutral cleanser diluted five or six times with water,
and wrung out well, and then wipe again with a dry cloth.
Do not use furniture wax or cleansers.
•
Never use thinners, benzine, insecticide sprays or other
chemicals on or near this unit, since these will corrode the
surface.
Specifications
Amplifier section
Continuous average power output of 80 watts* per
channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no
more than 0.08 %** total harmonic distortion.
Front (stereo) . . . . . . . . . . . . . . . . . . . . . . . . 80 W + 80 W
Power output (1 kHz, 6
Ω
, 1 %) . . . . . 140 W per channel
Maximum Effective Output Power
(JEITA) (1 kHz, 6
Ω
, 10 %) . . . . . . . . 150 W per channel
Guaranteed speaker impedance . . . . . . . . . . 6
Ω
to 16
Ω
* Measured pursuant to the Federal Trade Commission's
Trade Regulation rule on Power Output Claims for Amplifiers
** Measured by Audio Spectrum Analyzer
Audio section
Input (Sensitivity/Impedance)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 k
Ω
Signal-to-Noise Ratio (IHF-A network, 1 k
Ω
shorted)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 dB
Video Section
Signal level
Composite . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75
Ω
)
Tuner Section
Frequency Range (FM) . . . . . . . . . . . 87.5 MHz to 108 MHz
Antenna Input (FM) . . . . . . . . . . . . . . . . . .75
Ω
unbalanced
Frequency Range (AM) . . . . . . . . . . . .530 kHz to 1700 kHz
Antenna (AM). . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna
BLUETOOTH section
Version. . . . . . . . . . . . . BLUETOOTH Specification Ver. 3.0
Output . . . . . . . . . . . . . BLUETOOTH Specification Class 2
Estimated line-of-sight transmission distance*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About 10 m (33 ft.)
Frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . .2.4 GHz
Supported BLUETOOTH profiles. . . . . . . . . . . . . . . . .A2DP
Supported Codec . . . . . . . . . . .SBC (Subband Codec), AAC
* The line-of-sight transmission distance is an estimate.
Actual transmission distances supported may differ
depending on surrounding conditions.
Digital In/Out Section
HDMI terminal . . . . . . . . . . . . . . . . . . . . . . .Type A (19-pin)
HDMI output type . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 55 mA
USB terminal . . . . . USB2.0 Full Speed (Type A) 5 V, 0.5 A
Miscellaneous
Power Requirements . . . . . . . . . . . . . . . . .AC 120 V, 60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . 210 W
In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.35 W
Dimensions. . . . 435 mm (W) x 168 mm (H) x 320.5 mm (D)
17
1
/8 in. (W) 6
5
/8 in. (H) 12
5
/8 in. (D)
Weight (without package). . . . . . . . . . . . 8.0 k
g
(17 lb 10 oz)
VSX-532_CDC_En.book 35 ページ ２０１７年１月１２日 木曜日 午後３時１２分
