6
6
30
Chapter
Home Menu
Using the Home Menu
The following section shows you how to make detailed
settings to specify how you’re using the receiver, and also
explains how to fine-tune individual speaker system settings
to your liking.
Important
•
The OSD will not appear if you have connected using the
HDMI output to your TV. Use composite connections for
Home Menu.
•
If headphones are connected to the receiver, disconnect
them.
•
You can’t use the Home Menu when the
iPod/USB
input is
selected.
1
Switch on the receiver and your TV.
Press
RECEIVER
to switch on.
2
Switch the TV input to the input that connects this
receiver to the TV through the corresponding
composite cable.
3
Press ,
then
press
HOME MENU
.
The Home Menu appears on your TV. Use
///
and
ENTER
on the remote control to navigate through the
screens and select menu items. Press
RETURN
to exit
the current menu.
•
Press
HOME MENU
at any time to exit the Home
Menu.
4
Select the setting you want to adjust.
•
Auto MCACC
– This is a quick and effective automatic
surround setup (see
Automatically setting up for surround
sound (MCACC)
on page 18
).
•
Manual SP Setup
-
Speaker Setting
– Specify the size and number of
speakers you’ve connected (see below).
-
X.Over
– Specify which frequencies will be sent to the
subwoofer (
page 31
).
-
Channel Level
– Adjust the overall balance of your
speaker system (
page 31
).
-
Speaker Distance
– Specify the distance of your
speakers from the listening position (
page 32
).
•
Input Assign
– Specify what you’ve connected to the
ANALOG IN1
audio input (see
The Input Assign menu
on
page 32
).
•
Pre Out Setting
– Specify how to use the
PRE OUT SURR
BACK/FRONT HEIGHT
outputs (see
The Pre Out Setting
on
page 33
).
•
Auto Power Down
– Sets to automatically turn off the
power when the receiver has not operated for several hours
(see
The Auto Power Down menu
on page 33
).
•
FL Demo Mode
– Sets the demo display on the front panel
display (see
The FL Demo Mode menu
on page 33
).
•
HDMI Setup
– Set the audio return channel function and
set the HDMI input signal to Standby Through output or not
during standby (see
The HDMI Setup menu
on page 33
).
Manual speaker setup
This receiver allows you to make detailed settings to optimize
the surround sound performance. You only need to make
these settings once (unless you change the placement of your
current speaker system or add new speakers).
These settings are designed to fine-tune your system, but if
you’re satisfied with the settings made in
Automatically
setting up for surround sound (MCACC)
on page 18
, it isn’t
necessary to make all of these settings.
Important
•
Depending on the
Pre Out Setting
, there will be
differences in the speaker items that can be adjusted. The
OSD display for these operating instructions is an example
of when the
Pre Out Setting
is set to
Surr. Back
.
Speaker Setting
Use this setting to specify your speaker configuration (size,
number of speakers). It is a good idea to make sure that the
settings made in
Automatically setting up for surround sound
(MCACC)
on page 18
are correct.
1
Select ‘Manual SP Setup’ from the Home Menu.
2
Select ‘Speaker Setting’ from the Manual SP Setup
menu.
3
Choose the set of speakers that you want to set then
select a speaker size.
Use
/
to select the size (and number) of each of the
following speakers:
•
Front
– Select
LARGE
if your front speakers reproduce bass
frequencies effectively, or if you didn’t connect a
subwoofer. Select
SMALL
to send the bass frequencies to
the subwoofer.
RECEIVER
H o m e M e nu
1 . Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
R e t u r n
2.Manual SP Setup
Return
a.Speaker Setting
b.X.Over
c.Channel Level
d.Speaker Distance
2a.Speaker Setting
Front
Center
Surr
Surr. Back
Subwoofer:
Return
[ SMALL ]
[ SMALL ]
[ NO ]
YES
SMALL
