60
08
Control with HDMI function
Before using synchronization
Once you have finished all connections and settings, you must:
1 Put all components into standby mode.
2 Turn the power on for all components, with the power for the TV being turned on last.
3 Choose the HDMI input to which the TV is connected to this receiver, and see if video
output from connected components displays properly on the screen or not.
4 Check whether the components connected to all HDMI inputs are properly displayed.
About synchronized operations
Important
!
Synchronized operations are enabled when
Control Mode
is set to
ON
after setting
Control
in
HDMI Setup
to
ON
. For details, see
HDMI Setup
on
page 59
.
The
Control
with HDMI-compatible component connected to the receiver operates in sync as described below.
!
From the menu screen of the
Control
with HDMI-compatible TV, set audio to be played through this receiver,
and the receiver will switch to the synchronized amp mode.
!
When in the synchronized amp mode, you can adjust the receiver’s volume or mute the sound using the TV’s
remote control.
!
When in the synchronized amp mode, the synchronized amp mode is canceled when the receiver’s power is
turned off. To turn the synchronized amp mode back on, set audio to be played through the receiver from the
TV’s menu screen, etc. This receiver will power up and switch to the synchronized amp mode.
!
When the synchronized amp mode is canceled, the receiver’s power turns off if you were viewing an HDMI
input or a TV program on the TV.
!
When in the synchronized amp mode, the synchronized amp mode is canceled if an operation that produces
sound from the TV is performed from the TV’s menu screen, etc.
!
When the TV’s power is set to standby, the receiver’s power is also set to standby. (Only when the input for a
component connected to the receiver by HDMI connection is selected or when watching the TV.)
!
The receiver’s input switches automatically when the
Control
with HDMI-compatible component is played.
!
The receiver’s input switches automatically when the TV’s input is switched.
!
The synchronized amp mode remains in effect even if the receiver’s input is switched to a component other
than one connected by HDMI.
The operations below can also be used on Pioneer
Control
with HDMI-compatible TVs.
!
When the receiver’s volume is adjusted or the sound is muted, the volume status is displayed on the TV’s
screen.
!
When the OSD language is switched on the TV, the receiver’s language setting also switches accordingly.
Setting the PQLS function
PQLS (Precision Quartz Lock System) is a digital audio signal transfer control technology using the
Control
with
HDMI function. It offers higher-quality audio playback by controlling audio signals from the receiver to a PQLS
compatible player, etc. This enables removing jitter that has a negative effect on the quality of the sound and is
generated upon transmission.
!
On players compatible with PQLS Bit-stream, PQLS always works for all sources.
!
On players compatible with PQLS Multi Surround, PQLS works for all sources. Set the player’s audio output to
Linear PCM.
!
On players compatible with PQLS 2 ch Audio, PQLS only works when playing CDs.
Please refer to the operating instructions supplied with your player for more information.
This function is activated when
Control
is set to
ON
.
Tip
!
The PQLS setting is set at
PQLS
in
HDMI Setup
on the
HOME MENU
, but the setting can also be switched
with the remote control, as described below.
%
Press PQLS to select the PQLS setting.
The setting is displayed on the front panel display.
!
PQLS AUTO
– PQLS is enabled. A precision quartz controller in this receiver eliminates distortion caused by
timing errors (jitter), giving you the best possible digital-to-analog conversion when you use the HDMI inter-
face. This is valid as an HDMI function for PQLS-compatible players.
!
PQLS OFF
– PQLS is disabled.
About Sound Retriever Link and Stream Smoother Link
These are automatic functions allowing you to output optimum audio and video signals from the receiver using
the
Control
with HDMI function. When a player supporting the respective function is connected to the receiver
by HDMI, the sound/picture is optimized for the compressed audio/video file played on the player.
!
Depending on the compressed audio/video file format, it may not be operated automatically.
Sound Retriever Link
When playing a compressed audio file on the player, the file’s bitrate information is acquired using the
Control
with HDMI function, and the sound is optimized on the receiver based on this information.
To activate the Sound Retriever Link function, make the setting below.
1 Set the HDMI Setup’s Control to ON, and set the Control Mode setting to ON.
See
HDMI Setup
on
page 59
.
2 Set the S.RTRV (Auto Sound Retriever) setting to ON.
See
Setting the Audio options
on
page 63
.
Stream Smoother Link
Using the
Control
with HDMI function, the receiver automatically detects whether a compressed video file is
being played on the player, and if so automatically activates the Stream Smoother function.
To activate the Stream Smoother Link function, make the setting below.
1 Set the HDMI Setup’s Control to ON, and set the Control Mode setting to ON.
See
HDMI Setup
on
page 59
.
2 Set the STREAM (Stream Smoother) setting to AUTO.
See
Setting the Video options
on
page 65
.
