Listening to your system
5
5
37
4
62
7
•
Depending on the positions of the speakers and the sound
source, in some cases it may not be possible to achieve
good results. In this case, set the setting to
OFF
.
1
Switch the receiver into standby.
2
While holding down
PRESET
on the front panel, and
hold the
STANDBY/ON
for about two seconds.
UP MIX: OFF
appears and the Up Mix function turns off.
If you want to turn this function on, perform steps 1 and
2 again.
•
When set to
ON
, the (Up Mix) indicator on the front
panel lights.
Note
•
Set to
ON
regardless of this setting when playing DTS-HD
signals.
•
May automatically be set to
OFF
even when set to
ON
,
depending on the input signal and listening mode.
•
If the
Network Standby
is set to
ON
or
Standby Through
is not set to
OFF
, you may not be able to set the Up Mix
function.
•
HDMI Control should also be set to
OFF
, not
ON
.
Setting the Audio options
There are a number of additional sound settings you can
make using the
AUDIO PARAMETER
menu. The defaults, if
not stated, are listed in bold.
Important
•
Note that if a setting doesn’t appear in the
AUDIO
PARAMETER
menu, it is unavailable due to the current
source, settings and status of the receiver.
1
Press ,
then
press
AUDIO PARAMETER
.
2
Use
/
to select the setting you want to adjust.
Depending on the current status/mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
3
Use
/
to set it as necessary.
See the table below for the options available for each
setting.
4
Press
RETURN
to confirm and exit the menu.
C
SW
L
R
SL
SR
SBL
SBR
SBL
SBR
C
SW
L
R
SL
SR
UP MIX OFF
UP MIX ON
ENTER
MUTE
RETURN
AUDIO
PARAMETER
MENU
HOME
MENU
TOOLS
BAND
iPod CTRL
PTY
TOP
MENU
TUNE
TUNE
P
R
E
S
E
T
P
R
E
S
E
T
SLEEP
INPUT
RECEIVER
RECEIVER
SOURCE
RECEIVER
Setting/What it does
Option(s)
EQ
(Acoustic Calibration EQ)
Switches on/off the effect of Acoustic
Calibration EQ.
ON
OFF
S.DELAY
(Sound Delay)
Some monitors have a slight delay when
showing video, so the soundtrack will be
slightly out of sync with the picture. By adding
a bit of delay, you can adjust the sound to
match the presentation of the video.
0 to 500 ms (1
step : 5 ms)
Default:
0
MIDNIGHT
/
LOUDNESS
a
The
MIDNIGHT
allows you to hear effective
surround sound of movies at low volumes.
The
LOUDNESS
is used to get good bass and
treble from music sources at low volumes.
M/L OFF
MIDNIGHT
LOUDNESS
S.RTV
(Sound Retriever)
b
When audio data is removed during the
compression process, sound quality often
suffers from an uneven sound image. The
Sound Retriever feature employs new DSP
technology that helps bring CD quality sound
back to compressed 2-channel audio by
restoring sound pressure and smoothing
jagged artifacts left over after compression.
OFF
c
ON
DUAL MONO
d
Specifies how dual mono encoded Dolby
Digital soundtracks should be played.
CH1
– Channel 1
is heard only
CH2
– Channel 2
is heard only
CH1 CH2
– Both
channels heard
from front
speakers
F.PCM
(Fixed PCM)
This is useful if you find there is a slight delay
before
OFF
recognizes the PCM signal on a
CD, for instance.
When
ON
is selected, noise may be output
during playback of non-PCM sources. Please
select another input signal if this is a problem.
OFF
ON
VSX-1023_823_UCSMXCN_En.book 37 ページ ２０１２年１２月１８日 火曜日 午前１１時７分
