You can adjust the currently selected equalizer curve
setting as desired. Adjusted equalizer curve settings
are stored in
Custom1
or
Custom2
.
!
A separate
Custom1
curve can be created for
each source. If you make adjustments when a
curve other than
Custom2
is selected, the equali-
zer curve settings will be stored in
Custom1
.
!
A
Custom2
curve that is common for all sources
can be created. If you make adjustments when
the
Custom2
curve is selected, the
Custom2
curve will be updated.
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to cycle between equalizer band and
level.
3
Press
M.C.
to switch to equalizer band and then
turn
M.C.
to select.
100Hz
—
315Hz
—
1.25kHz
—
3.15kHz
—
8kHz
4
Press
M.C.
to switch to level and then turn
M.C.
to adjust.
Adjustment range:
+6
to
–
6
Loudness
(loudness)
Loudness compensates for deficiencies in the low-
and high-frequency ranges at low volume.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the desired setting.
OFF
(off)
—
Low
(low)
—
Mid
(mid)
—
High
(high)
3
Press
M.C.
to confirm the selection.
SW setting 1
(subwoofer on/off setting)
This unit is equipped with a subwoofer output which
can be turned on or off.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the desired setting.
Normal
(normal phase)
—
Reverse
(reverse
phase)
—
OFF
(subwoofer off)
3
Press
M.C.
to confirm the selection.
SW setting 2
(subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to cycle between cut-off frequency and
output level of subwoofer.
3
Press
M.C.
to switch to cut-off frequency and then
turn
M.C.
to select cut-off frequency.
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
4
Press
M.C.
to switch to output level and then turn
M.C.
to adjust output level.
Adjustment range:
+6
to
-24
HPF setting
(high pass filter adjustment)
When you do not want low sounds from the subwoo-
fer output frequency range to play from the front or
rear speakers, turn on the HPF (high pass filter). Only
frequencies higher than those in the selected range
are output from the front or rear speakers.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the cut-off frequency.
OFF
(off)
—
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
3
Press
M.C.
to confirm the selection.
Bass booster
(bass boost)
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to adjust the level.
Adjustment range:
0
to
+6
3
Press
M.C.
to confirm the selection.
SLA
(source level adjustment)
SLA
(Source Level Adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
!
When selecting FM as the source, you cannot
switch to
SLA
.
!
Settings are based on the FM volume level, which
remains unchanged.
Before adjusting source levels, compare the FM
volume level with the level of the source you wish
to adjust.
!
The AM volume level can also be adjusted with
this function.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to adjust the source volume.
Adjustment range:
+4
to
–
4
3
Press
M.C.
to confirm the selection.
Note
Operation is complete even if the menu is can-
celled before being confirmed.
Initial Settings
1
Press SRC/OFF and hold until the unit
turns off.
2
Press M.C. and hold until the initial set-
ting menu appears in the display.
En
19
English
Section
02
Operating this unit
Summary of Contents for Super Tuner IIID DEH-P6200BT
Page 115: ...Es 115 Español ...
