108
The System Setup and Other Setup menus
12
Auto Power Down
The power can be set to turn off automatically if no operation has been performed for a specific amount of
time with no audio or video signals being input to the receiver. When using ZONE 2, ZONE 3 or HDZONE, the
ZONE 2, ZONE 3 or HDZONE power can also be set to turn off, but for ZONE 2, ZONE 3 or HDZONE the power
turns off automatically after the amount of time set here even if signals are being input or operations have been
performed.
Different times can be set for the main zone, ZONE 2, ZONE 3 and HDZONE.
1 Select ‘Auto Power Down’ from the Other Setup menu.
2 Select the zone you want to set and set the time after which the power turns off.
!
MAIN
– The time can be selected from among “
15 min
”, “
30 min
”, “
60 min
” and “
OFF
”. The power turns off
after there has been no signal and no operation for the selected time.
!
ZONE 2
– The time can be selected from among “
30 min
”, “
1 hour
”, “
3 hours
”, “
6 hours
”, “
9 hours
” and
“
OFF
”. The power turns off after the selected time.
!
ZONE 3
– The time can be selected from among “
30 min
”, “
1 hour
”, “
3 hours
”, “
6 hours
”, “
9 hours
” and
“
OFF
”. The power turns off after the selected time.
!
HDZONE
– The time can be selected from among “
30 min
”, “
1 hour
”, “
3 hours
”, “
6 hours
”, “
9 hours
” and
“
OFF
”. The power turns off after the selected time.
Note
Depending on the connected devices, the Auto Power Down function may not work properly due to excessive
noise or other reasons.
Volume Setup
You can set the maximum volume of this receiver or specify what the volume level will be when the power is
turned on.
1 Select ‘Volume Setup’ from the Other Setup menu.
2 Select the Power ON Level setting you want.
The volume can be set so that it is always set to the same level when the receiver’s power is turned on.
!
LAST
(default) – When the power is turned on, the volume is set to the same level as when the power was last
turned off.
!
“
---
” – When the power is turned on, the volume is set to minimum level.
!
–80.0dB
to
+12.0dB
– Specify the volume to be set when the power is turned on, in steps of 0.5 dB.
It is not possible to set a volume level greater than the value specified at Volume Limit setup (see below).
3 Select the Volume Limit setting you want.
Use this function to limit the maximum volume. The volume cannot be increased above the level set here, even by
operating
VOLUME
button (or the dial on the front panel).
!
OFF
(default) – The maximum volume is not limited.
!
–20.0dB
/
–15.0dB
/
–10.0dB
/
–5.0dB
/
0.0dB
– The maximum volume is limited to the value set here.
4 Select the Mute Level setting you want.
This sets how much the volume is to be turned down when
MUTE
is pressed.
!
FULL
(default) – No sound.
!
–40.0dB
/
–20.0dB
– The volume will be turned down to the level specified here.
5 When you’re finished, press RETURN.
You will return to the
Other Setup
menu.
Remote Control Mode Setup
!
Default setting:
1
This sets this receiver’s remote control mode to prevent erroneous operation when multiple units of the receiver
are being used.
1 Select ‘Remote Control Mode Setup’ from the Other Setup menu.
2 Select the Remote Control Mode setting you want.
3 Select ‘OK’ to change the remote control mode.
4 Follow the instructions on the screen to change the remote control’s setting.
.
5 When you’re finished, press RETURN.
You will return to the
Other Setup
menu.
Software Update
Use this procedure to update the receiver’s software and check the version. There are two ways to update: via the
Internet and via a USB memory device.
Updating via the Internet is performed by accessing the file server from the receiver and downloading the file.
This procedure is only possible if the receiver is connected to the Internet.
Updating via a USB memory device is performed by downloading the update file from a computer, reading this
file onto a USB memory device then inserting this USB memory device into the USB port on the receiver’s front
panel. With this procedure, the USB memory device containing the update file must first be inserted into the USB
port on the receiver’s front panel.
!
If an update file is provided on the Pioneer website, download it onto your computer. When downloading an
update file from the Pioneer website onto your computer, the file will be in ZIP format. Unzip the ZIP file before
saving it on the USB memory device. If there are any old downloaded files or downloaded files for other models
on the USB memory device, delete them.
http://www.pioneer.com.sg (for Southeast Asia)
http://www.pioneer-india.in (for India)
http://www.pioneerhongkong.com.hk (for Hong Kong)
!
If an update file does not exist in the Pioneer’s website, updating the software for the receiver is not necessary.
Important
!
DO NOT unplug the power cord during updating.
!
When updating via the Internet, do not disconnect the LAN cable. When updating via a USB memory device,
do not disconnect the USB memory device.
!
If updating is interrupted before it is completed, start updating over from the beginning.
!
The receiver’s settings may be reset when the software is updated. Information on the models for which the
settings are reset is provided on the Pioneer website. Check the website before updating.
1 Select ‘Software Update’ from the Other Setup menu.
2 Select the update procedure.
!
Update via Internet
– The receiver checks whether updatable software is available via the Internet.
!
Update via USB Memory
– The receiver checks whether the USB memory device inserted into the USB port
on the receiver’s front panel contains updatable software.
“
Accessing
” is displayed and the update file is checked. Wait a while.
