Pioneer SC-LX73, Operating Instructions Manual

Page: 89 / 144

Controlling the rest of your system (In case of SC-LX83) 10
89
En
Setting the remote control operation
mode
• Default setting: ON
When the r emote cont r ol ope r ation mode is tu r ned on
and the r eceive r ’s input is switched, the r emote cont r ol
display and ope r ation mode switch automatically to that
input. Select
OFF
if you do not want the r emote cont r ol’s
function to switch automatically when the r eceive r ’s
input is switched.
1
1 While pressing MULTI OPERATION, press HOME
MENU.
The r emote display shows SETUP MENU .
2 Use
/
to select ‘OPERATION MODE’, then press
ENTER.
Check that the units a r e pai r ed. If SYNCHRO ON is
displayed, pai r ing has been pe r fo r med p r ope r ly, so
p r oceed to step 3. If RF MODE ONLY flashes, pai r ing has
not been pe r fo r med p r ope r ly, so pe r fo r m this p r ocedu r e
again afte r pe r fo r ming pai r ing (see
Pairing the RF adapter
and remote control on page 87).
3 Use
/
to select ‘SYNCHRO ON’ or ‘SYNCHRO
OFF’, then press ENTER.
The r emote display shows
OK
to confi r m the setting.
4 Press and hold MULTI OPERATION for a couple of
seconds to exit and store the operation(s).
Precautions when using the Omni-
Directional RF Remote Control
Precautions regarding wavelength
• This r emote cont r ol is designed to p r event othe r
pe r sons f r om eavesd r opping on the t r ansmitted
signals, but p r ecautions should nonetheless be
taken against the chance that othe r pe r sons’ could
inte r cept and listen to the signals t r ansmitted. Given
that this r emote cont r ol p r oduces r adio wave
t r ansmissions, anothe r pe r son could delibe r ately use
a r eceive r to attempt to inte r cept such t r ansmissions.
As a r esult, this device should not be used to play
impo r tant t r ansmissions demanding p r ivacy.
This r emote cont r ol utilizes the 2.4 GHz f r equency band.
This band is also used by a va r iety of othe r devices as
noted below. In pa r ticula r , devices not often cognizant to
the use r a r e listed in item 2.
1 Examples of common devices utilizing the 2.4 GHz
band:
• Co r dless phone
• Co r dless facsimile
• Mic r owave oven
• Wi r eless LAN r oute r
• Wi r eless AV device
• Wi r eless cont r olle r s fo r games
• Mic r owave the r apeutic devices
•
Bluetooth
wi r eless technology devices
2 Other devices using 2.4 GHz:
• Shoplifting-p r evention systems
• Amateu r wi r eless r adio
• Dist r ibution cont r ol systems at facto r ies and
wa r ehouses
• Railway and eme r gency vehicle wi r eless
identification systems
When such devices a r e used simultaneously with this
r emote cont r ol, signal inte r fe r ence may occu r , r esulting
in signal d r opouts.
To imp r ove r eception quality, t r y the following:
• Tu r n off the othe r device emitting r adio waves.
• Place the inte r fe r ing device fa r the r away (Move both
the r emote cont r ol and RF adapte r away f r om the
inte r fe r ing device).
Do not use this r emote cont r ol in the following locations,
since t r ansmission inte rr uption may r esult:
• Locations whe r e anothe r device using the same 2.4
GHz f r equency is being used, such as a Bluetooth
wi r eless technology device o r wi r eless LAN, o r in the
vicinity whe r e the magnetic field, static elect r icity, o r
r adio wave inte r fe r ence f r om anothe r device may
occu r (depending on the envi r onment, r adio waves
may not t r ansmit effectively).
• Move the r adio fa r the r away.
• If visual noise appea r s on the television sc r een, it is
possible that this r emote cont r ol is p r oducing
adve r se influence on the antenna input of the
television, video device, BS tune r , o r CS tune r . Move
this r emote cont r ol fa r the r away f r om the antenna
input of the affected device.
Note
1 • When the r emote cont r ol’s input is switched, the r eceive r ’s input also switches, but fo r functions fo r which the r emote cont r ol di r ect function
(page 82) is set to off, when the r emote cont r ol’s input is switched, the r eceive r ’s input does not switch and only the r emote cont r ol unit’s
ope r ating sc r een switches.
• The r emote cont r ol ope r ation mode is only valid when the r emote cont r ol ope r ation selecto r switch is set to
SOURCE
.
SC-LX83_73_DLPW.book 89 ページ ２０１０年５月１９日 水曜日 午後２時７分