Pioneer SC-LX73, Operating Instructions Manual

Page: 87 / 144

Controlling the rest of your system (In case of SC-LX83) 10
87
En
Pairing the RF adapter and remote control
Pai r ing is necessa r y in o r de r to use the RF
communications function. Pe r fo r m the ope r ation below
afte r connecting the RF adapte r and r eceive r .
1 Switch on the receiver.
2 Set the RF Remote Setup on this receiver’s Other
Setup menu to ON.
Fo r details, see
RF Remote Setup (SC-LX83 only)
on
page 115.
3 Press the SETTING button on the front of the RF
adapter.
RF adapte r ’s LED blinks r ed.
4 While pressing MULTI OPERATION, press VIDEO
PARAMETER on the remote control.
The r emote display shows
PAIRING
.
5 Press ENTER on the remote control.
AUTHORIZATION flashes and pai r ing is pe r fo r med.
When pai r ing is successful, SUCCESS is displayed and
pai r ing is completed. RF adapte r ’s LED lights g r een.
If
ERROR
is displayed, pai r ing has not been successful.
Check the connections and distance with the RF adapte r ,
then sta r t ove r f r om step 1.
The r emote cont r ol unit’s r eceive r ope r ation mode must
be set to “RF” in o r de r to ope r ate the r eceive r with RF two-
way communications. Make this setting as desc r ibed at
Operating this receiver by RF communications below.
Operating this receiver by RF
communications
Use this p r ocedu r e to make the r emote cont r ol settings
to ope r ate the r eceive r using RF two-way
communications. The settings can be made individually
fo
r the main zone, ZONE 2 and ZONE 3. Connect the
r eceive r and RF adapte r and pai r the RF adapte r and
r emote cont r ol unit befo r ehand.
1 While pressing MULTI OPERATION, press HOME
MENU.
The r emote display shows SETUP MENU .
2 Use
/
to select ‘IR/RF SELECT’, then press
ENTER.
Check that the units a r e pai r ed. If RECEIVER MAIN is
displayed, pai r ing has been pe r fo r med p r ope r ly, so
p r oceed to step 3. If RF MODE ONLY flashes, pai r ing has
not been pe r fo r med p r ope r ly, so pe r fo r m this p r ocedu r e
again afte r pe r fo r ming pai r ing (see
Pairing the RF adapter
and remote control on page 87).
3 Use
/
to select the receiver zone for which you
want to use RF two-way communications, then press
ENTER.
4 Use
/
to select ‘RF MODE’, then press ENTER.
1
Select
IR MODE
to r etu r n to ope r ation by inf r a r ed signal.
5 If you want to operate other zones with RF two-
way communications, repeat steps 3 and 4.
Operating other components by RF
communications
Up to 4 othe r components connected to the r eceive r can
be ope r ated by RF communications. Use the IR blaste r to
communicate between the RF adapte r and othe r
components, and switch the r emote cont r ol’s setting to
RF. The r emote cont r ol’s setting can be switched
individually fo r each input.
Note
1 When RECEIVER is selected and RF MODE is set at step 3, HMG NET RADIO , ADAPTER , iPod USB and TUNER a r e automatically set to the
RF mode. Note that
RF MODE
cannot be set fo r
OPTION 1
and
OPTION 2
.
To mount on a shelf above the
component
Double-faced
tape
Rack
Remote cont r ol senso r
To mount on the component
Remote cont r ol senso r
Double-
faced tape
SC-LX83_73_DLPW.book 87 ページ ２０１０年５月１９日 水曜日 午後２時７分