background image

4

En

Effective Combination of 
Subwoofer and Satellite 
Speakers

• When the subwoofer is combined with 

satellite speakers in a total system, the sound 
characteristics produced are like those 
shown in the accompanying graph, 
depicting the enhancement of the bass 
frequencies. 
This is particularly effective for reproducing 
ground rumbles and other deep sound 
effects found in movies. 

Connections and Use

Panel facilities

Front panel

Rear panel

1 Power Indicator

When the power is turned ON, the indicator 
changes from flashing to steadily lighted blue. 
In the standby mode, the indicator lights red.

2 Volume knob (MIN/MAX)

• Sets the subwoofer volume.
• With this unit, the bass level can be 

independently set, so do not turn up the 
bass on the receiver.

3 Line Level Input terminal (LINE IN)
4 Auto Standby switch (AUTO STANDBY)

• Turning the Auto Standby function on or 

off.

5 Power switch (POWER)

• Switches the subwoofer between ON and 

OFF.

6 AC  IN

• Connect the power cord to a AC socket.

Satellite s Subwoofer

Only the satellite speaker

Frequency (Hz)

Re

s

p

onse (dB)

1

MIN

MAX

LINE IN

ON

AUTO STANDBY

ON

POWER

AC IN

6

5

4

3

2

• The power is still supplied even when the 

power indicator is off. The power plug 
(interrupter) must be unplugged in order 
to completely cut the power supply. When 
not using this product for long periods of 
time, such as when traveling, unplug the 
power cord (interrupter) from the power 
outlet for safety purposes. Failure to do so 
could lead to fire.

• The volume knob is factory set at the MIN 

position.

• The default setting for AUTO STANDBY 

switch is ON.

Auto standby function

When there is no (or only very weak) input 
signal for a period of about ten minutes, the 
power mode automatically changes to 
standby (power indicator lights red). The 
power automatically turns on when a signal 
is input. The auto standby function is 
deactivated when AUTO STANDBY switch is 
set to OFF.

• There may be cases where a connected 

component outputs noise or some other 
non-audio signal which causes the 
subwoofer to automatically power on 
when in Auto Standby mode. If this 
happens, switch off the Auto Standby 
mode and switch the subwoofer on/off 
manually.

Important

Important

Important

S-31W_En.book  4 ページ  2012年1月17日 火曜日 午前9時28分

Summary of Contents for S-31W









Reviews: