Pioneer PDP-R06C Service Manual Download Page 38

Page: 38 / 90

PDP-R06G

6.4 LIST OF RS-232C COMMANDS

RS-232C commands can be used in Service Factory mode. Before using RS-232C commands, it is necessary to change the factory
presetting.
Also the RS-232C commands for the panel is not listed. Please refer to panle's service manual.

Command Operation

Remarks

BSL

Adjust side mask B

CNG

Clearing MR NG information

CHR

Clearing MR Hour meter

DW*

Decreasing the adjustment value by*

*:1-9, 0 (0 means 10), F (making the adjustment value the minimum)

FAN

Turning Service Factory mode off.

FAY

Turning Service Factory mode on.

FST

Final Set Up

GSL

Adjusting side mask G

INA

Selection of tuner for terrestrial analog signals.

INC***

Selection of tuner for terrestrial digital signals.

INH

Selection of SD card/PCMCIA card

INPS01

Input selection: input 1

INPS02

Input selection: input 2

INPS03

Input selection: input 3

INPS04

Input selection: input 4

INPS05

Input selection: input 5

OSDS00

Turning On-Screen Display off

Permit On-Screen Display.

OSDS01

Turning On-Screen Display on

Prohibit On-Screen Display.

POF

Turning the power off.

PON

Turning the power on.

QS1

Obtaining the version data for each device.

QS6

Obtaining the any version.

QMT

Obtaining the MR temperature information.

QNG

Obtaining NG data of the MR.

RSL

Adjustment od side mask R

UP*

Increasing the adjustment value by *

*:1-9, 0 (0 means 10), F (making the adjustment value the maximum)

ZME

Initializing of the EEPROM video data

Summary of Contents for PDP-R06C



























































































Search results

Summary of Contents for PDP-R06C

Reviews:

Related manuals for PDP-R06C

Brands by name

Popular brands

Pioneer PDP-R06C, Service Manual

Search results

Summary of Contents for PDP-R06C

Reviews:

Related manuals for PDP-R06C

Brands by name

Popular brands