PDP-504CMX/1
107
5
6
7
8
5
6
7
8
C
D
F
A
B
E
1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
O P T I O
P A
A S K
( + )
E
N
M
T T
R
N
I N 1 – G 3 2 – R G B – 4 M X
OPTION mode
No.
Function/Display
Content
Remarks
1
PATTERN MASK (+)
For selecting Pattern mask of IC4
A lower layer exists.
2
FULL MASK (+)
For selecting raster mask of IC4
A lower layer exists.
3
DYNAMIC RANGE
ON
⇔
OFF
The last setting is not stored in memory (initial setting: ON).
4
EDID WRITE MODE
DISABLE
⇔
ENABLE
The last setting is not stored in memory (initial setting: DISABLE).
5
INTEGRATOR MODE
DISABLE
⇔
ENABLE
Initial setting: ENABLE
Select the main item "OPTION" using the MUTE key then select the subitems shown in the table below using the
5
or
∞
key.
Note:
• For PATTERN MASK (+) and FULL MASK (+), press the SET key to switch to the lower layer.
• Adjustments No. 3 to 5 above are not required for servicing.
Note:
• White balance adjustment.(From No.1 to No.6). (Refer to 136 pages of the " [W/B-adjustment procedurs]")
• Adjustments No. 7: [ABL] above are not normally required, unless so instructed by Service Information, etc.
"
∗∗∗
" in the table above represents the adjustment value.
The value of each subitem can be changed using the
2
or
3
key.
"(PTO)" and "(ABx)" in the table above represent the following:
No.
Function/Display
Content
Adjustable Range
Corresponding 232C
Command
1
PANEL R HIGH <=>
:
∗∗∗
(PTO)
Panel W/B R-HIGH adjustment
PRH
2
PANEL G HIGH <=>
:
∗∗∗
(PTO)
Panel W/B G-HIGH adjustment
PGH
3
PANEL B HIGH <=>
:
∗∗∗
(PTO)
Panel W/B B-HIGH adjustment
PBH
4
PANEL R LOW <=>
:
∗∗∗
(PTO)
Panel W/B R-LOW adjustment
PRL
5
PANEL G LOW <=>
:
∗∗∗
(PTO)
Panel W/B G-LOW adjustment
PGL
6
PANEL B LOW <=>
:
∗∗∗
(PTO)
Panel W/B B-LOW adjustment
PBL
7
ABL LEVEL <=>
:
∗∗∗
(ABx)
Power consumption adjustment
ABL
000 to 511
000 to 511
000 to 511
000 to 999
000 to 999
000 to 999
000 to 999
Each time the
5
or
∞
key is pressed, the subitems are changed, as follows:
Indication
Table
PT1
For PC and NTSC
PT2
For PAL, For PC (48Hz)
Indication
Table
AB1
For 60Hz and 75Hz video
AB2
For 50Hz video, For 48Hz PC
AB3
For PC
4. COMMON-PANEL2
1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
C OMMO
P A N E L
: 1 2 8 ( P T 1 )
R – H I G H
< = >
N – P A N E L 2
I N 1 – G 3 2 – R G B – 4 M X
