manualshive.com logo in svg

Pioneer ELITE VSX-LX505, Instruction Manual

The Pioneer ELITE VSX-LX505 is a top-of-the-line AV receiver that boasts impressive features and exceptional sound quality. With its user-friendly interface, navigating this receiver couldn't be easier. For your convenience, an Instruction Manual is available for free download from manualshive.com, ensuring you get the most out of your audio experience.

Share
Download
background image

173

Setup

• 

Measurement may not be possible if the test tone is to loud or too soft. Tap 

"Level Adjust" to adjust the volume of the test tone.

7.  When measurement is complete, "Calculating results" is displayed on the 

screen. Tap "Transfer to your product" to transfer the measurement data to 

the unit.

8. 

Disconnect the speaker setup microphone. 

• 

When measurement is performed with Dirac Live, selection in "Advanced 

MCACC" - "Manual MCACC" ( 

→

p154

) and "MCACC Data Check" 

( 

→

p156

) of the Home screen is no longer available. Furthermore, the 

measurement results are also reflected in "System Setup" - "Speaker" - 

"Distance" ( 

→

p135

) of the Home screen, and you will no longer be able to 

change the values. (The setting units are displayed as "msec".)

Using Dirac Live

You can use the equalizer function based on the measurements results of Dirac 

Live. From "Room EQ" - "Dirac Live" ( 

→

p93

) in "AV Adjust", select from 

"Slot1" to "Slot3". Note that the same data is saved in all of the slots, but you are 

able to create your own original sound quality in the following "Manual Adjust" 

section.

• 

In the Home screen, when the number of speaker channels, etc., is changed 

in "System Setup" - "Speaker" - "Configuration" ( 

→

p132

), the measurement 

results are deleted.

• 

When using Dirac Live, signals with a sampling frequency of 32 kHz are not 

supported.

Manual Adjust

You can adjust the sound quality to your own original one by modifying the 

equalizer curves based on the volume level of the speakers automatically 

measured with Dirac Live. Modify the equalizer on the Pioneer Remote App.

•  To adjust the sound quality with "Manual Adjust", it is first necessary to 

measure the speakers of this unit with Dirac Live ( 

→

p168,

 

p172

).

• 

This function cannot be used when speaker measurement is done with Full 

Auto MCACC ( 

→

p153,

 

p170

).

Modifying the equalizer

1.  Start the Pioneer Remote App and tap the unit when displayed.

2.  Tap " " in the top left of the Pioneer Remote App screen to display a list of 

menus, then tap "Manual Adjust".

3.  Select the slot to modify from "Slot1" to "Slot3", then tap "Next".

• 

The measurement results from Dirac Live are registered in all of the slots 

as the default values.

4. 

After selecting the speaker to adjust first, modify the equalizer curve.

Summary of Contents for ELITE VSX-LX505





















































































































































































































Reviews:

No comments

Related manuals for ELITE VSX-LX505

Panasonic CS-HZ25UKE User Manual preview
CS-HZ25UKE
Brand: Panasonic Pages: 24
Icom ic-2730A Programming Manual preview
ic-2730A
Brand: Icom Pages: 2
Icom IC-25A Instruction Manual preview
IC-25A
Brand: Icom Pages: 36
Icom IC-2340H Instruction Manual preview
IC-2340H
Brand: Icom Pages: 60
Icom IC-2300H Instructions preview
IC-2300H
Brand: Icom Pages: 2
Icom ic-f5021 Service Manual preview
ic-f5021
Brand: Icom Pages: 38
Icom IC-03AT Instruction Manual preview
IC-03AT
Brand: Icom Pages: 48
Icom IC-R72 Service Manual preview
IC-R72
Brand: Icom Pages: 57
Icom IC-281H Instruction Manual preview
IC-281H
Brand: Icom Pages: 60
Icom IC-2725E Instruction Manual preview
IC-2725E
Brand: Icom Pages: 96
Icom IC-7000 Installing Manual preview
IC-7000
Brand: Icom Pages: 4
Icom D-STAR ID-4100A Service Manual preview
D-STAR ID-4100A
Brand: Icom Pages: 46
Icom D-STAR ID-4100A Manual preview
D-STAR ID-4100A
Brand: Icom Pages: 36
Icom D-STAR ID-31A; D-STAR ID-31E Service Manual preview
D-STAR ID-31A; D-STAR ID-31E
Brand: Icom Pages: 41
Icom IC-208H Adjustment Procedure preview
IC-208H
Brand: Icom Pages: 12
Icom IC-M802 Quick Reference Manual preview
IC-M802
Brand: Icom Pages: 5
Icom IC-400PRO Service Manual preview
IC-400PRO
Brand: Icom Pages: 36
JAMO DMR 61 Instruction Manual preview
DMR 61
Brand: JAMO Pages: 18

Brands by name

Popular brands

Load more brands