Pioneer ELITE VSX-LX505 Instruction Manual Download Page 126

Page: 126 / 212

126

Setup

Input/Output Assign

TV Out / OSD

Make settings for TV output and On-Screen Displays (OSD) that appear on the

TV.

HDMI Out (Default Value: MAIN)

Select the HDMI jack to be connected with the TV.

•

If devices with different resolutions are connected to HDMI OUT MAIN jack

and SUB jack, images are output with the lower resolution.

MAIN

When connecting the TV to the HDMI OUT MAIN jack

SUB

When connecting the TV to the HDMI OUT SUB jack

MAIN+SUB

When connecting to both the MAIN and SUB jacks

Dolby Vision (Default Value: MAIN)

To output Dolby Vision video from the player to a TV that supports Dolby Vision,

select either the HDMI OUT MAIN jack or HDMI OUT SUB jack to which the

Dolby Vision-supported TV is connected. This setting is only necessary if you

have set "HDMI Out" to "MAIN+SUB" and you have connected a TV to both the

MAIN and SUB jacks.

MAIN

To output Dolby Vision video to a Dolby Vision-supported TV

connected to the HDMI OUT MAIN jack

SUB

To output Dolby Vision video to a Dolby Vision-supported TV

connected to the HDMI OUT SUB jack

Off

After selecting "MAIN" or "SUB", if the video on the TV does

not appear correctly

Upscaling (Default Value: Off)

When using a TV that supports 4K/8K, video signals input at 1080p can be

automatically upscaled to 4K/8K for output. Video signals that are input at 4K

can also automatically be output as 8K. Note that to output as 8K, set "HDMI

4K/8K Signal Format" (

→

p127

) to "8K Standard" or "8K Enhanced", and you

need to connect to a TV that is compatible with the 8K signal format with an

HDMI cable.

• If the TV does not support the 4K/8K resolution with the same frequency

as the frequency of HDMI input video signals, upscaling to 4K or 8K is not

correctly performed. Check the frequency of 4K/8K resolution supported

by the TV, and change the resolution of the video signals input from the AV

component.

Off

When this function is not used

• Select "Off" if your TV does not support 4K/8K.

Auto

When this function is used

Super Resolution (Default Value: 2)

When you have set "Upscaling" to "Auto", you can select the degree of video

signal correction from "Off" and between "1" (weak) and "3" (strong).

Summary of Contents for ELITE VSX-LX505





















































































































































































































Search results

Summary of Contents for ELITE VSX-LX505

Reviews:

Related manuals for ELITE VSX-LX505

Brands by name

Popular brands

Pioneer ELITE VSX-LX505, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX505

Reviews:

Related manuals for ELITE VSX-LX505

Brands by name

Popular brands