Pioneer ELITE VSX-LX304 Instruction Manual Download Page 59

Page: 59 / 180

≫

≫

≫

≫

≫

≫

Connecting ZONE B

Connecting a Pre-main Amplifier, etc. (ZONE B)

While performing playback through speakers (ZONE A) connected to the unit,

you can enjoy the audio of the same source at the same time with the pre-main

amplifier or the transmitter of the wireless headphones connected to the ZONE

B LINE OUT jack. Use an analog audio cable to connect the ZONE B LINE OUT

jack of this unit and the LINE IN jack of the pre-main amplifier or the transmitter of

the wireless headphones.

For playback, press the button on the remote controller to display "AV Adjust",

and select the audio output destination. (

p97

)

Setup

•

A setting must be made in order to output the audio to ZONE B. Press

the remote controller to display the Home screen, then set "System Setup" -

"Speaker" - "Configuration" - "Zone 2 Preout" (

p128

) to "Zone B".

Analog audio cable

LINE

1.005 mm

Premain Amp.

Transmitter

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands