Pioneer ELITE VSX-LX304 Instruction Manual Download Page 132

Page: 132 / 180

132

≫

≫

≫

≫

≫

≫

Dolby Enabled Speaker

Change the settings of Dolby Enabled Speakers.

Setting Item

Default Value

Setting Details

Dolby Enabled

Speaker to Ceiling

6.0 ft/1.80 m

Set the distance between the Dolby Enabled

Speaker and the ceiling. Select between

"0.1 ft/0.03 m" and "15.0 ft/4.50 m" (0.1 ft/0.03 m

units).

• The unit of distance (ft/m) is displayed using the

unit selected for the "Distance" setting.

Reflex Optimizer

Off

You can enhance the reflection effect of Dolby

Enabled Speakers from the ceiling.

"Off": When this function is not used

"On": When this function is used

•

The function is not effective if the listening mode

is Pure Direct.

•

This setting can be selected when "Configuration" - "Height 1 Speaker" / "Height 2

Speaker" is set to "Dolby Speaker".

Speaker Virtualizer

The Speaker Virtualizer function can be switched between On and Off

Setting Item

Default Value

Setting Details

Speaker

Virtualizer

"On": The listening mode with virtual speaker effect

such as F.S.Surround can be selected.

"Off": The listening mode with virtual speaker effect

such as F.S.Surround cannot be selected.

Audio Adjust

Dual Mono/Mono

Change the settings of multiplex audio playback.

Setting Item

Default Value

Setting Details

Dual Mono

Main

Set the audio channel or language to be output

when playing multiplex audio or multilingual

broadcasts, etc.

"Main": Main channel only

"Sub": Sub channel only

"Main/Sub": Main and sub channels are output at

the same time.

• For multiplex audio broadcasts, pressing the

button on the remote controller will display "1+1"

on the main unit’s display.

Mono Input

Channel

Left + Right

Set the input channel to play 2-ch digital sources

such as Dolby Digital, or 2-ch analog/PCM sources

in the Mono listening mode.

"Left": Left channel only

"Right": Right channel only

"Left + Right": Left and right channels

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands