Pioneer ELITE VSX-LX304 Instruction Manual Download Page 131

Page: 131 / 180

131

≫

≫

≫

≫

≫

≫

Channel Level

Adjust the volume level of each speaker.

Setting Item

Default Value

Setting Details

Front Left

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Center

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Front Right

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Height 1 Left

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

• Depending on the use of the ZONE speakers, it

may not be possible to select this setting.

Height 1 Right

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

• Depending on the use of the ZONE speakers, it

may not be possible to select this setting.

Height 2 Left

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

• Depending on the use of the ZONE speakers, it

may not be possible to select this setting.

Setting Item

Default Value

Setting Details

Height 2 Right

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

• Depending on the use of the ZONE speakers, it

may not be possible to select this setting.

Surround Right

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Surr Back Right

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

• Depending on the use of the ZONE speakers, it

may not be possible to select this setting.

Surr Back Left

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

• Depending on the use of the ZONE speakers, it

may not be possible to select this setting.

Surround Left

0.0 dB

Select a value between "-12.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Subwoofer

0.0 dB

Select a value between "-15.0 dB" and "+12.0 dB"

(in 0.5 dB increments). A test tone will be output

each time you change the value. Select the desired

level.

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands