En
56
10
Controlling the rest of your system
Note
!
You can cancel or exit any of the steps by
pressing
RCU SETUP
.
!
After one minute of inactivity, the remote
automatically exits the operation.
Operating multiple receivers
Up to four receivers can be operated discretely
using this receiver’s remote control when using
multiple receivers, provided they are of the
same model as this receiver. The receiver to be
operated is switched by inputting the preset
code to set the remote control setting.
!
Set the remote modes on the receivers before
using this function (see
Remote Control Mode
Setup
on page 74 ).
1 Press and hold RCU SETUP, then press
‘4’ for three seconds.
Release the button after the LED flashes once.
The LED continues to flash.
!
To cancel the preset setup mode press
RCU SETUP
.
2 Press the number button for the
receiver (“Receiver 1” to “Receiver 4”) you
wish to operate.
For example, to operate “Receiver 2”, press ‘
2
’.
If the LED lights for one second and continues
to flash, the setting has been successfully
completed.
When the preset code is input, the LED flashes
three times to indicate that the setting has
failed.
Setting the remote to control
other components
Most components can be assigned to one of
the input function buttons (such as
DVD
or
CD
)
using the component’s manufacturer preset
code stored in the remote.
However, there are cases where only certain
functions may be controllable after assigning
the proper preset code, or the codes for the
manufacturer in the remote control will not
work for the model that you are using.
If you can’t find a preset code that matches the
component you want to control, you can still
teach the remote individual commands from
another remote control (see
Programming sig-
nals from other remote controls
on page 57 ).
!
For greater convenience, assign the TV
connected to the
MONITOR OUT
terminal to
the
TV CTRL
button, and assign your satellite/
cable receiver or set-top box connected to the
TV/SAT
input terminal to the
TV/SAT
input
button. If a single device is connected to both
terminals, that device should be assigned to
both the
TV CTRL
and
TV/SAT
input buttons.
!
Devices may be assigned to the following
input function buttons.
INPUT SELECT
iPod
USB
OPTION
TUNER
SIRIUS
ADPT
HMG
CD
TV
RCU SETUP
SOURCE
RECEIVER MULTI
OPERATION
BDR
SAT
BD
DVD
DVR
HDMI
RECEIVER
TV CTRL
Selecting preset codes directly
1 Press and hold RCU SETUP, then press
‘1’ for three seconds.
Release the button after the LED flashes once.
The LED continues to flash.
!
To cancel the preset setup mode press
RCU SETUP
.
Controlling the rest of your system
About the Remote Setup menu
The Remote Setup mode is set by pressing the
number button while pressing
RCU SETUP
. The
different items on the Remote Setup menu are
described below. For their setting procedures,
refer to the explanations for the respective
items.
Setting
What it does
Preset
recall
Preset codes can be set for the various
input functions. The remote control
codes of a number of other devices
(including products of other brands)
are preset in the remote control to
allow these devices to be operated.
See
Selecting preset codes directly
on
page 56 .
Code
learning
If the desired operations cannot be
performed even though you have set
the preset codes, the remote control
signals of other devices can be learned
directly. See
Programming signals from
other remote controls
on page 57 .
Multi
operation
A series of the remote control opera-
tions for starting listening or viewing
can be programmed. Multiple remote
control codes can be set for the differ-
ent input functions. See
Multi Opera-
tion and System Off
on page 58 .
System
off
This is a function for automatically
turning off the power of devices con-
nected to the receiver. Multiple remote
control codes can be set, as desired.
See
Multi Operation and System Off
on
page 58 .
Setting
What it does
Direct
function
This is a setting for changing only the
remote control unit’s operation screen,
without changing the receiver’s input,
when the remote control unit’s input
function buttons are pressed. This
is convenient for using the remote
control unit for devices not connected
to the receiver. See
Direct function
on
page 57 .
Erase
learning
This function is used to erase remote
control codes that have been learned.
Codes learned for the different input
functions can be erased individually.
See
Erasing one of the remote control
button settings
on page 57 .
Back light
The backlight lighting pattern can be
selected from among four modes, in
consideration of convenience and
battery service life. See
Setting the
backlight mode
on page 58 .
Reset
function
This is a function for resetting preset
codes that have been set. Key reset-
ting can be done for individual input
functions. See
Erasing all learnt set-
tings that are in one input function
on
page 57 .
All reset
This is a function for resetting all
remote control unit settings you have
made to the defaults set upon ship-
ment from the factory. See
Resetting
the remote control settings
on page 59 .
Change
RC mode
If you have multiple Pioneer receivers,
amplifiers, etc., this setting can be
used to prevent other units from oper-
ating simultaneously when the remote
control unit is operated. See
Operating
multiple receivers
on page 56 .
Summary of Contents for Elite VSX-52
Page 1: ...VSX 53 VSX 52 ...
