Pioneer Elite SC-LX704 Instruction Manual Download Page 222

Page: 222 / 225

222

≫

≫

≫

≫

≫

≫

General Specifications

Amplifier Section

Rated Output Power (FTC) (North American)

With 8 ohm loads, both channels driven, from 1 kHz; rated 140 watts per

channel minimum RMS power, with no more than 0.08% total harmonic

distortion from 250 milliwatts to rated output.

Rated Output Power (IEC) (European)

11 ch × 215 W at 6 ohms, 1 kHz, 1 ch driven of 1% THD

Maximum Effective Output Power (JEITA)

260 W at 6 ohms, 1 kHz, 1 ch driven of 10% THD

Multi channel simultaneous power output (1 kHz, 1%, 8Ω)

880 W (11ch total)

THD+N (Total Harmonic DisNoise)

0.04% (1 kHz, 100 W)

Input Sensitivity and Impedance

200 mV/82 kΩ (LINE (RCA))

3.5 mV/47 kΩ (PHONO MM)

Rated RCA Output Level and Impedance

1 V/470 Ω (PRE OUT)

1 V/470 Ω (SUBWOOFER PRE OUT)

200 mV/1.2 kΩ (ZONE B /ZONE 2 / ZONE 3 LINE OUT)

2 V/1.2 kΩ (ZONE 2 / ZONE 3 PRE OUT)

Phono Maximum Input Signal Voltage

70 mV (MM 1 kHz 0.5%)

Tone Control Characteristics (MAIN)

±10 dB, 20 Hz (BASS)

±10 dB, 20 kHz (TREBLE)

Tone Control Characteristics (ZONE 2)

±10 dB, 100 Hz (BASS)

±10 dB, 10 kHz (TREBLE)

Signal to Noise Ratio

108 dB (IHF-A, LINE IN, SP OUT)

90 dB (IHF-A, PHONO IN, SP OUT)

Speaker Impedance

4 Ω - 16 Ω

Headphone Rated Output

57 mW + 57 mW (32 Ω, 1 kHz, 10% THD)

Video Section

Signal level

1 Vp-p/75 Ω (Composite Video)

1 Vp-p/75 Ω (Component Video Y)

0.7 Vp-p/75 Ω (Component Video Pb/Pr)

Maximum resolution supported by component video

480i/576i

Tuner Section

FM Tuning Frequency Range

87.5 MHz - 107.9 MHz (North American)

87.5 MHz - 108.0 MHz, RDS (Others)

50 dB quieting sensitivity (FM MONO)

1.0 μV, 11.2 dBf (IHF, 75 Ω)

AM Tuning Frequency Range

530 kHz - 1710 kHz (North American)

522/530 kHz - 1611/1710 kHz (Others)

Preset Channel

Network Section

Ethernet LAN

10BASE-T/100BASE-TX

Summary of Contents for Elite SC-LX704


































































































































































































































Search results

Summary of Contents for Elite SC-LX704

Reviews:

Related manuals for Elite SC-LX704

Brands by name

Popular brands

Pioneer Elite SC-LX704, Instruction Manual

Search results

Summary of Contents for Elite SC-LX704

Reviews:

Related manuals for Elite SC-LX704

Brands by name

Popular brands