Advanced Operations
38
En <DRB1388>
Advanced Operations
MODE
NORMAL/DJ
PLAY/PAUSE
6
JOG MODE
RELEASE/
START
TOUCH/
BRAKE
A
B
C
HOT CUE
REC MODE
Jog dial
Scratch play
★
This function is not supported when the rear panel mode select
switch (MODE NORMAL/DJ) is set to the NORMAL position.
When the jog mode is set to VINYL mode ON, pressing the jog dial’s top
panel while rotating the dial will cause audio and video to be output in
proportion to the direction and speed of jog dial rotation.
1. Press the JOG MODE select button so that the VINYL
mode indicator lights.
2. During playback, press the top of the jog dial.
¶
Playback will slow and come to a stop (the time required to com-
plete stop can be set independently).
¶
If the jog dial is rotated as playback slows but before it has com-
pletely stopped, sound will be interrupted suddenly, and will then
start again, but in the direction corresponding to the direction the
jog dial is rotated in step 3.
3. Rotate the jog dial in the desired direction of playback.
¶
Playback will occur in proportion to the direction and speed of jog
dial rotation.
4. Release hand from surface of jog dial.
¶
Playback will return to its original status (the time required until
full acceleration can be set independently).
■
To set the deceleration time (time until playback fully stops
when jog dial surface is pressed)
Rotate the TOUCH/BRAKE response dial.
¶
The time till playback stops changes.
■
To set the acceleration time (time until playback fully re-
gains original speed when hand is released from jog dial
surface)
Rotate the RELEASE/START response dial.
¶
The time till playback returns to normal speed changes.
Spin play
★
This function is not supported when the rear panel mode select
switch (MODE NORMAL/DJ) is set to the NORMAL position.
With VINYL mode ON, press the surface of the jog dial, or press the
PLAY/PAUSE
(
6
) button to set the unit to pause, then rotate the jog
dial quickly; even if you remove your hand from the jog dial, playback will
occur in proportion to the direction and speed of the jog dial rotation.
Hot cue
★
This function is not supported when the rear panel mode select
switch (MODE NORMAL/DJ) is set to the NORMAL position.
This function allows playback to be started quickly from one of three
points (A, B, C), by previous setting of cue point and loop information.
¶
Storing to memory may not be possible while the jog dial’s audio/
video memory status display is flashing.
■
Setting hot cue point
1. Press the HOT CUE REC MODE button so that the HOT
CUE A, B, and C button indicators light red.
2. During playback, pause mode or cue standby mode, find
the point you wish to use as the hot cue, and at that point
press the button (A, B, or C) in which you wish to store
the cue information.
¶
The button memory will recorded with the time position data and
playback method.
¶
The pressed button will flash red for about 2 seconds, then light
steadily.
¶
During DVD playback, a thumbnail of the hot cue point will be
displayed on the preview monitor screen.
¶
If the
HOT CUE
button is pressed during the loop setting mode
(while
LOOP OUT/OUT ADJUST
button and
LOOP IN/REALTIME
CUE
buttons are flashing), the currently playing loop information
will be stored in memory.
¶
If a memory card is loaded, the data recorded to the
HOT CUE
button will be stored on the memory card; in this way, the previ-
ously set information can be called up quickly when playing the
same disc at a later date (
☞
P.42).
■
Starting a hot cue
1. Press the HOT CUE REC MODE button so that the HOT
CUE A, B, and C button indicators light green or orange.
¶
Buttons containing stored hot cue points will light green.
¶
Buttons containing stored loop information will light orange.
¶
Buttons without any stored information will not light.
2. During playback, pause, or cue standby mode, press one
of the buttons with stored information (A, B, or C).
¶
During playback, pause mode or cue standby mode, if a green or
orange lighted button is pressed, playback will begin instantly based
on the information recorded in the button. In this case, cue point
information stored in the normal
CUE
button, or loop information
stored in the
RELOOP/EXIT
button will not be overwritten, but
remain valid.
¶
Pressing a
HOT CUE
button with stored loop information causes
loop playback to begin instantly based on the stored information.
In this case, the
RELOOP/EXIT
button can be used to cancel the
loop playback just as with normal loop play, and the
LOOP OUT/
OUT ADJUST
button can likewise be used to modify the loop-out
point. If loop information is modified, the loop information stored
in the button will simultaneously be modified.
¶
If a memory card is loaded, inserting a disc will allow previously
recorded hot cue and loop information for that disc to be restored
(
☞
P.43).
* When playing a DVD that prohibits title or other searches, it may be
impossible to begin playback from the hot cue point.
In this case, the prohibited mark will appear in the display and the
similar mark
will appear on the preview monitor screen.
* In the case of MP3, hot cue is supported only within one and the
same folder.
Buttons and controls with the
mark are disabled when
the mode select switch is set to NORMAL.
