Pioneer DEQ-S1000A, User Manual

Page: 1 / 32

English
Before You Start
Thank you for purchasing this PIONEER product
To ensure proper use, please read through this guide before using this product.
It is especially important that you read and observe WARNINGS and CAUTIONS
in this guide. Please keep the guide in a safe and accessible place for future
reference.
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
Information for users on collection and disposal of old
equipment and used batteries
(Symbol for equipment) (Symbol examples for batteries)
These symbols on the products, packaging, and/or accompanying documents
mean that used electrical and electronic products and batteries should not
be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used
batteries, please take them to applicable collection points in accordance
with your national legislation.
By disposing of these products and batteries correctly, you will help to save
valuable resources and prevent any potential negative effects on human health
and the environment which could otherwise arise from inappropriate waste
handling.
For more information about collection and recycling of old products and
batteries, please contact your local municipality, your waste disposal service or
the point of sale where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer
and ask for the correct method of disposal.
CAUTION
• This product is evaluated in moderate and tropical climate condition under the
Audio, video and similar electronic apparatus - Safety requirements, IEC 60065.
Connections
WARNING
Important
• When installing this unit in a vehicle without an ACC (accessory) position on
the ignition switch, failure to connect the red cable to the terminal that detects
operation of the ignition key may result in battery drain.
ACC position
No ACC position
• Use this unit with a 12-volt battery and negative grounding only. Failure to do so
may result in a fire or malfunction.
• To prevent a short-circuit, overheating or malfunction, be sure to follow the
directions below.
−Disconnect the negative terminal of the battery before installation.
−Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape
around wiring that comes into contact with metal parts to protect the wiring.
−Place all cables away from moving parts, such as the shift lever and seat rails.
−Place all cables away from hot places, such as near the heater outlet.
−Do not connect the yellow cable to the battery by passing it through the hole
to the engine compartment.
−Cover any disconnected cable connectors with insulating tape.
−Use a fuse of the rating prescribed.
−Never wire the negative speaker cable directly to ground.
−Never band together negative cables of multiple speakers.
• The graphical symbol placed on the product means direct current.
• Check the connections of the power supply and speakers if this unit fuse blows.
Determine and resolve the cause, then replace the fuse with and identical
equivalent.
• Always install this unit on a flat surface.
Do not install this unit on a surface that is not flat or on a surface with a
protrusion. Doing so could result in malfunction.
• When installing this unit, do not allow parts such as extra screws to get caught
between this unit and the automobile.
Doing so could cause malfunction.
• Do not allow this unit to come into contact with liquids. Electrical shock could
result.
Also, damage to this unit, smoke, and overheating could result from contact with
liquids.
The surfaces of the amplifier and any attached speakers may also heat up and
cause minor burns.
• Do not attempt to disassemble or modify this unit. Doing so may result in fire,
electric shock or other malfunction.
This unit
This unit provides a variety of sound effects by intuitive operation using a
smartphone.
FUSE 10A
Power cord input
Parking brake cord input
Subwoofer output
Rear output/Middle range output
Front output/High range output
RCA input
Remote control sensor input
USB port
Reset button
Power indicator
INPUT select switch
DSP MODE select switch
Remote control sensor
Preparing the remote control
Remove the insulation sheet before use.
How to replace the battery
Insert the battery with the plus (+) and minus (–) poles orientated properly.
WARNING
• Do not ingest the battery, Chemical Burn Hazard.
(The remote control supplied with) This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and
keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
• Batteries (battery pack or batteries installed) must not be exposed to excessive
heat such as sunshine, fire or the like.
CAUTION
• There is a danger of explosion if the battery is incorrectly replaced. Replace only
with the same or equivalent type.
• When disposing of used batteries, please comply with governmental regulations
or environmental public institution’s rules that apply in your country / area.
Connection of power cord and speaker
Cut the attached power cord and then connect it to the vehicle.
The wiring harness kit (sold separately) is also available to connect the cord.
Refer to:
• Connections when using
the speaker input wire
• Connections when using
the RCA input jack
To power cord input
Power cord
Yellow
To terminal supplied with power, regardless of ignition switch position
Red
To electric terminal controlled by ignition switch (12 V DC) ON/OFF
Blue/white
Connect to the system control terminal of the power amp (max. 300 mA 12 V
DC).
Connections when using the RCA input jack
Connect the car stereo RCA output jack and the RCA input jack of this unit.
Slide the INPUT select switch to the RCA position.
To RCA input
RCA cable (sold separately)
To RCA output
Car stereo / navigation system
Note
• The input signal of Car stereo / navigation system is 2ch. The output signal
of this unit will not be reflected even when changing settings other than the
corresponding channel of the car stereo / navigation system.
• Connect the front RCA output of the car stereo / navigation system.
• Make sure to connect with the speaker input if your vehicle has no ACC
(accessory) position.
This unit activates with the power of the car stereo / navigation system.
This unit may not activate depending on the type of car stereo / navigation
system.
Connections when using the speaker input
wire
Connect the car stereo speaker output wires to this unit using the power cord.
Slide the INPUT select switch to the SP position.
To power cord input
Power cord
Orange
Orange/black
Brown
Brown/black
Left +
Left −
Right +
Right −
Car stereo / navigation system
Note
• The input signal of Car stereo / navigation system is 2ch. The output signal
of this unit will not be reflected even when changing settings other than the
corresponding channel of the car stereo / navigation system.
• Connect the front speaker output of the car stereo / navigation system.
Parking brake cable connections
Connect to the parking brake switch using the parking brake cord.
To parking brake cord input
Parking brake cord
Used to detect the ON/OFF status of the parking brake. This lead must be
connected to the power supply side of the parking brake switch.
Power supply side
Parking brake switch
Ground side
Note
When the parking brake cable is not connected, a part of the exclusive application
(Sound Tune) function is limited.
Name of each remote control button
VOLUME –
MUTE
SRC (source)
Left
Press to select the previous track / song.
Right
Press to select the next track / song.
PLAY/PAUSE
A
Press and hold to change the connection mode (for iPhone® / AOA connection
of smartphone (Android)).
B
Press and hold to change the connection mode (OTG connection of
smartphone (Android)).
Black (ground)
To vehicle (metal) body
Left
Right
Front speaker (STD) or high range speaker (NW)
Rear speaker (STD) or middle range speaker (NW)
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Connections when using the amplifier (sold
separately)
System remote control
Connect to Blue/white cable.
Power amp (sold separately)
Connect with RCA cable (sold separately)
To front output (STD) or high range output (NW)
Front speaker (STD) / High range speaker (NW)
To rear output (STD) or middle range output (NW)
Rear speaker (STD) / Middle range speaker (NW)
To subwoofer output (STD) or low range output (NW)
Subwoofer (STD) / Low range speaker (NW)
• Make sure to connect with the speaker input if your vehicle has no ACC
(accessory) position.
This unit activates with the power of the car stereo / navigation system.
This unit may not activate depending on the type of car stereo / navigation
system.
Installation
This unit
Important
• Check all connections and systems before final installation.
• Do not use unauthorized parts as this may cause malfunctions.
• Consult your dealer if installation requires drilling of holes or other modifications
to the vehicle.
• Do not install this unit where:
−it may interfere with operation of the vehicle.
−it may cause injury to a passenger as a result of a sudden stop.
• Install this unit away from hot places such as near the heater outlet.
• To enable the setting value, change the setting of the INPUT select switch or the
DSP MODE switch and turn the ACC switch OFF/ON.
1. Set the DSP MODE select switch.
2. Set the INPUT select switch.
3. Tighten the screws on each side, then fix the unit.
Bracket
Screw (Washer-faced head 4 mm × 8 mm)
Screw (Tapping screw 4 mm × 12 mm)
Hole (2 mm to 2.5 mm)
Car mat or chassis (installation example)
Download Sound Tune
To use this unit, download Sound Tune to the iPhone or smartphone (Android).
Enter the search term "Pioneer Sound Tune" in the search window or search from
the following QR code.
WARNING
Do not attempt to operate the application while driving. Make sure to pull off the
road and park your vehicle in a safe location before attempting to use the controls
on the application.
Sound Tune can do the following.
Playing songs saved on iPhone / smartphone (Android)
Playable song formats depend on your device. For details, please read the
instruction manual of your device.
Effect settings of iPhone / smartphone (Android) songs and the car stereo /
navigation system sound
• Super “Todoroki” Sound
• Live Simulation
Various settings of this unit
• Standard Mode (Front / Rear / Subwoofer)
• Network Mode (3 Way Network)
• Speaker Setting
−Graphics Equalizer
Remote control sensor
1. Connect the remote control sensor to the remote control sensor input .
Place the light receiving part of the remote control sensor in a place that can
receive the remote control signal.
Wire the cable so that it does not interfere with driving.
Remote control sensor
−Time Alignment
−Network Filter
−Speaker Level
• Fader / Balance
• Source Calibration
For details of each function, please refer to Popup Help in Sound Tune.
How to Use This Unit
Depending on the connection method of the iPhone / smartphone (Android), this
unit can be used as follows.
When using this unit alone (When not
connecting an iPhone or smartphone
(Android))
The unit outputs the sound source of the car stereo / navigation system. Only
the volume adjustment and mute functions can be operated with the supplied
remote control.
For audio adjustment, connection of an iPhone / smartphone (Android) is
necessary.
When connecting an iPhone / smartphone
(Android) to use
The unit can be used in the following four pattern modes.
When using the remote control, press the SRC button to switch the mode.
The mode switches in the order of Car Stereo mode, Through mode, Smartphone
mode, and Mix mode.
Car Stereo mode
The unit outputs the sound source of the car stereo / navigation system by
passing through the iPhone / smartphone (Android).
Smartphone mode
The unit outputs the sound source of the iPhone / smartphone (Android).
Through mode
The unit outputs the sound source of the car stereo / navigation system without
passing through the iPhone / smartphone (Android). (It is the same output as
using this unit alone)
This mode is used when video and audio are misaligned during video playback in
the Car Stereo mode.
Mix mode
The unit mixes and outputs the sound of the iPhone / smartphone (Android) and
the sound of the car stereo / navigation system.
Use this mode when you want to use the voice guidance of the car stereo /
navigation system while listening to the source of the iPhone / smartphone
(Android). In this case, turn off the source of the car stereo / navigation system
and set it so that only the voice guidance is output.
Depending on the car stereo / navigation system, this mode may not be available.
The available functions differ depending on the connection method of the iPhone
/ smartphone (Android).
Device iPhone Smartphone (Android)
Connection method - AOA*1 OTG*2
Car Stereo mode
✔
-(*3)
✔
Smartphone mode
✔ ✔ ✔
(*4)
Through mode
✔ ✔ ✔
Mix mode
✔ ✔ ✔
(*4)
*1: AOA (Android Open Accessory) is an interface standard for using USB-loaded
products as accessories on Android terminals.
*2: OTG (On-The-Go) is an interface standard that connects USB devices and USB
devices directly. Smartphones (Android) cannot be charged using the OTG
connection. Pay attention to the battery level of the smartphone (Android).
*3: For the AOA connection, you cannot use the Car Stereo mode. The operation is
the same as Through mode.
*4: For the OTG connection, sounds from applications other than Sound Tune
cannot be output from this unit.
Note
• When the iPhone / smartphone (Android) is disconnected, some functions such
as Super “Todoroki” Sound and Live Simulation cannot be used.
Also, even if the iPhone / smartphone (Android) is connected, the above
functions may not be used under the following conditions.
−When selecting Through mode
−When playing media by applications other than Sound Tune
• Although this unit can be connected to smartphones (Android), it does not
guarantee the availability of all terminals.
Depending on the smartphone (Android), the unit may not be operated with an
AOA connection. In this case, use an OTG connection.
If all else fails, it might be a terminal that cannot be connected or that is out of
order. Please contact your dealer or service agent.
Connecting the Smartphone to This Unit
For iPhone users
USB port
USB cable (for Type-A)
Lightning® – USB cable (genuine product or sold separately)
iPhone
For smartphone (Android) users (AOA connection)
USB port
USB cable (for Type-A)
USB - micro USB cable (sold separately)
Smartphone (Android)
For smartphone (Android) users (OTG connection)
USB port
USB cable (for Type-A)
USB A-A cable (sold separately)
USB OTG cable (sold separately)
Smartphone (Android)
Note
Smartphone (Android) cannot be charged using the OTG connection.
About USB devices
• For details on handling the iPhone / smartphone (Android), please read each
manual.
• Please understand that we do not assume responsibility for compensation even
if data, etc. are lost at the time of use in combination with this unit.
• Be sure to fix the iPhone / smartphone (Android) when using it in combination
with this unit.
About connection with this unit
• Do not connect devices other than the iPhone / smartphone (Android) (such as
USB fan).
• It is not compatible with connection using USB hub.
Using Sound Tune
When connecting an iPhone or smartphone (Android) to this unit, a message
is displayed on the iPhone or smartphone (Android). Sound Tune starts when
startup is allowed.
Tap the icon at the bottom of the screen to start the operation.
How to reset
Reset this unit if it does not operate properly or you want to return the setting
value to the factory default.
1. Press the reset button while the unit is in operation.
The settings are initialized when the ignition switch is turned off (ACC OFF).
The factory default setting is applied when the unit is turned on next time.
When the sound does not sound
If you cannot hear the sound after installing this unit, carry out the following.
• Make sure that the iPhone / smartphone (Android) is connected correctly with a
USB cable.
• Make sure that switching of OTG / AOA is performed correctly.
• Turn the ACC switch OFF / ON.
Please contact your dealer or service agent if improvements are not made even if
you perform the above.
About the protection function
This product has a protection function. When this product detects something
abnormal, the following functions will operate to protect the product and speaker
output.
• The power indicator will turn Red, blink Red, and then the product will power off
in the situations outlined below.
−If the speaker output terminal and speaker wire are short-circuited.
−If a DC voltage is applied to the speaker output terminal.
−If a USB power supply detects something abnormal
−If a USB line has a communication error
Please contact your dealer or service agent if improvements are not made even
after you try turning the ACC switch OFF / ON or removing/reinserting the USB.
Specifications
GENERAL
POWER SOURCE 14.4V DC
(10.8-15.1V allowable)
GROUNDING SYSTEM Negative type
MAX. CURRENT CONSUMPTION 9.2A
DIMENSIONS 170(W) x 40(H) x 95(D)<mm>
FUSE 10A
WEIGHT 0.59kg
AUDIO
MAX POWER 50W x 4
50Wx2ch/4Ω + 70Wx1ch/2Ω (for SUB-WOOFER)
CONTINUOUS POWER 22W x 4
(50Hz to 15kHz, 5%THD, 4Ω LOAD, Both Channels Driven)
LOAD IMPEDANCE 4Ω
(4 - 8Ω(2Ω for 1ch) allowable)
PREOUT OUTPUT LEVEL (MAX) 4.0V
IMPEDANCE 250Ω
FREQUENCY RESPONSE 10Hz to 20kHz (+0dB , -1dB)
S/N RATIO 105dB
THD 0.01%
EQUALIZER (13BAND GRAPHIC EQUALIZER)
FREQUENCY 50Hz, 80Hz, 125Hz, 200Hz, 315Hz, 500Hz
800Hz, 1.25kHz, 2kHz, 3.15kHz, 5kHz, 8kHz, 12.5kHz
GAIN ±12dB(0.1dB step)
SPEAKER SETTING
<STANDARD MODE>
FRONT/REAR (HPF)
FREQUENCY
50Hz, 63Hz, 80Hz, 100Hz, 125Hz, 160Hz, 200Hz
SLOPE
0dB(Pass), -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct
SUB WOOFER (LPF)
FREQUENCY
50Hz, 63Hz, 80Hz, 100Hz, 125Hz, 160Hz, 200Hz
SLOPE
0dB(Pass), -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct
GAIN -24 - +10dB (1dB/Step)
PHASE NORMAL/REVERSE
SPEAKER LEVEL -24 - +10dB (1dB/Step)
TIME ALIGNMENT 0cm - 350cm (2.5cm/step)
<NETWORK MODE>
HIGH (HPF) FREQUENCY 1.25kHz, 1.6kHz, 2kHz, 2.5kHz, 3.15kHz
4kHz, 5kHz, 6.3kHz, 8kHz, 10kHz, 12.5kHz
SLOPE -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct
MID (LPF) FREQUENCY 1.25kHz, 1.6kHz, 2kHz, 2.5kHz, 3.15kHz
4kHz, 5kHz, 6.3kHz, 8kHz, 10kHz, 12.5kHz
SLOPE
0dB(Pass), -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct
MID (HPF) FREQUENCY 25Hz, 31.5Hz, 40Hz, 50Hz, 63Hz, 80Hz
100Hz, 125Hz, 160Hz, 200Hz, 250Hz
SLOPE
0dB(Pass), -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct
SUB WOOFER (LPF)
FREQUENCY 25Hz, 31.5Hz, 40Hz, 50Hz, 63Hz, 80Hz
100Hz, 125Hz, 160Hz, 200Hz, 250Hz
SLOPE 0dB(Pass), -12dB/oct, -18dB/oct
-24dB/oct, -30dB/oct, -36dB/oct
GAIN -24 - +10dB (1dB/Step)
PHASE NORMAL/REVERSE
SPEAKER LEVEL -24 - +10dB (1dB/Step)
TIME ALIGNMENT 0cm - 350cm (2.5cm/step)
USB
USB STANDARD SPEC. USB2.0 High Speed
MAX CURRENT SUPPLY 1.5A
Trademarks
iPhone, and Lightning are trademarks of Apple Inc., registered in the U.S.
and other countries.
Use of the Made for Apple badge means that an accessory has been
designed to connect specifically to the Apple product(s) identified in the
badge, and has been certified by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or its compliance
with safety and regulatory standards.
Please note that the use of this accessory with an Apple product may affect
wireless performance.
UNIVERSAL SOUND PROCESSOR
PROCESSEUR AUDIO UNIVERSEL
Instruction Manual
Mode d’emploi
5707000012571V-A
DEQ-S1000A