Installation without the rubber bush (Fig. 6)
Fig. 6
Removing the Unit (Fig. 7) (Fig. 8)
Fig. 7
Fig. 8
Nut (5 mm)
Dashboard
Drill a 5.5 – 6.0 mm
diameter hole.
Screw (5
×
16 mm)
Nut (5 mm)
Screw
Strap
Be sure to use the strap to secure the back
of the unit in place. The strap can be bent
by hand to the desired angle.
Installation
<ENGLISH>
Note:
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver’s
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• The semiconductor laser will be damaged if it
overheats, so don’t install the unit anywhere hot —
for instance, near a heater outlet.
• If installation angle exceeds 60° from horizontal,
the unit might not give its optimum performance.
(Fig. 4)
Fig. 4
60
°
Connecting the Units
<ENGLISH>
This Product
Antenna jack
15 cm
(5-7/8 in.)
15 cm
(5-7/8 in.)
IP-BUS input (Blue)
15 cm
(5-7/8 in.)
23 cm
(9 in.)
15 cm
(5-7/8 in.)
+
≠
+
≠
+
≠
+
≠
Right
Left
White/black
Gray/black
Subwoofer
Front speaker
Front speaker
Subwoofer
Gray
White
Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
Note:
Change the Initial Setting of this Product (refer to the
Operation Manual). The subwoofer output of this unit is
monaural.
Subwoofer output or Non Fading output
(SUBWOOFER or NON-FADING OUTPUT)
Front output (FRONT OUTPUT)
Rear output (REAR OUTPUT)
Green
Green/black
Violet
Violet/black
Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
Multi-CD player
(sold separately)
IP-BUS cable
Fuse holder
Fuse resistor
Fig. 3
7
When using a Subwoofer without using a different amp (sold separately)
DIN Front/Rear-mount
This unit can be properly installed either from “Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush (Fig. 5)
Fig. 5
182
53
Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)
Frame
Insert the supplied extraction keys into the unit, as
shown in the figure, until they click into place. Keeping
the keys pressed against the sides of the unit, pull the
unit out.
Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly possible using the top
and bottom tabs. To secure, bend the
tabs 90 degrees.)
Dashboard
Rubber bush
Screw
