background image

INST

ALLA

TION MANUAL

 MANUEL D’INST

ALLA

TION

DEH-P400UB

<KMINX>  <07H00000>

  Printed in China

  Imprimé en Chine

<YRD5170-A/S> UC

Installation

English

Installation

English

Connecting the unit

English

 Note

• 

Check all connections and systems before final in-

stallation.

• 

Do not use unauthorized parts. The use of unau-

thorized parts may cause malfunctions.

• 

Consult with your dealer if installation requires drill-

ing of holes or other modifications of the vehicle.

• 

Do not install this unit where:

— 

it may interfere with operation of the vehicle.

— 

it may cause injury to a passenger as a result 

of a sudden stop.

• 

The semiconductor laser will be damaged if it over-

heats. Install this unit away from hot places such as 

near the heater outlet.

• 

Optimum performance is obtained when the unit is 

installed at an angle of less than 60°.

60

°

DIN Front/Rear-mount

This unit can be properly installed either from  
"Front" (conventional DIN Front-mount) or 
"Rear" (DIN Rear-mount installation, utilizing 
threaded screw holes at the sides of unit 
chassis). For details, refer to the following 
installation methods.

DIN Front-mount

Installation with the rubber bush 

1.  Insert the mounting sleeve into the 

dashboard.

•  When installing in a shallow space, use a 

supplied mounting sleeve. If there is enough 

space behind the unit, use factory supplied 

mounting sleeve.

2.  Secure the mounting sleeve by 

using a screwdriver to bend the 
metal tabs (90°) into place.

3.  Install the unit as illustrated.

53

53

1

1

182

182

Removing the Unit

1.  Extend top and bottom of the trim 

ring outwards to remove the trim 
ring. When reattaching the trim ring, 
push the trim ring onto the unit until 
it clicks. (If the trim ring is attached 
upside down, the trim ring will not 
fit properly.)

•  It becomes easy to remove the trim ring if the 

front panel is released.

2.  Insert the supplied extraction keys 

into both sides of the unit until they 
click into place.

3.  Pull the unit out of the dashboard.

DIN Rear-mount

1.  Extend top and bottom of the trim 

ring outwards to remove the trim 
ring. When reattaching the trim ring, 
push the trim ring onto the unit until 
it clicks. (If the trim ring is attached 
upside down, the trim ring will not 
fit properly.)

•  It becomes easy to remove the trim ring if the 

front panel is released.

2. Determine the appropriate position 

where the holes on the bracket and 
the side of the unit match.

3. Tighten two screws on each side.

•  Use either truss screws (5 mm × 8 mm) or 

flush surface screws (5 mm × 9 mm), depend-

ing on the shape of screw holes in the bracket.

Fastening the front panel

If you do not plan to detach the front panel, 
the front panel can be fastened with supplied 
screw.

 Note

•  When this unit is installed in a vehicle without 

ACC (accessory) position on the ignition switch, 

red cable must be wired to the terminal that can 

detect the operation of the ignition key. Otherwise, 

battery drain may result.

ACC

ON

S

T

A

R

T

O

FF

      

ON

S

T

A

R

T

O

FF

ACC position

      

No ACC position

•  Use this unit in other than the following condi-

tions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative 

grounding.

— Speakers with 50 W (output value) and 4 ohm 

to 8 ohm (impedance value).

•  To prevent short-circuit, overheating or malfunc-

tion, be sure to follow the directions below.

— Disconnect the negative terminal of the battery 

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive 

tape around them where they lie against metal 

parts.

— Place all cables away from moving parts, such 

as gear shift and seat rails.

— Place all cables away from hot places, such as 

near the heater outlet.

— Do not pass the yellow cable through a hole 

into the engine compartment to connect to a 

battery.

— Cover any disconnected cable connectors with 

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of 

this unit in order to share the power to other 

equipment. Current capacity of the cable is 

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly 

to ground.

— Never band together multiple speaker’s nega-

tive cables.

•  Control signal is output through blue/white cable 

when this unit is powered on. Connect it to an ex-

ternal power amp’s system remote control or the 

vehicle’s auto-antenna relay control terminal (max. 

300 mA, 12 V DC). If the vehicle is equipped with a 

glass antenna, connect it to the antenna booster 

power supply terminal.

•  Never connect blue/white cable to external power 

amp’s power terminal. Also, never connect it to 

the power terminal of the auto antenna. Other-

wise, battery drain or malfunction may result.

•  IP-BUS connectors are color-coded. Be sure to 

connect connectors of the same color.

•  Black cable is ground. This cable and other 

product’s ground cable (especially, high-current 

products such as power amp) must be wired sepa-

rately. Otherwise, fire or malfunction may result if 

they are accidentally detached.

Dashboard

Mounting sleeve

Rubber bush

Screw

Trim ring

Trim ring

Factory radio mounting bracket

Screw

Screw

Dashboard or Console

Summary of Contents for DEH-P400UB - Premier Radio / CD

Page 1: ... mm or flush surface screws 5 mm 9 mm depend ing on the shape of screw holes in the bracket Fastening the front panel If you do not plan to detach the front panel the front panel can be fastened with supplied screw Note When this unit is installed in a vehicle without ACC accessory position on the ignition switch red cable must be wired to the terminal that can detect the operation of the ignition...

Page 2: ...US input Blue IP BUS cable Multi CD player sold separately 1 5 m 4 ft 9 in USB cable Connect to separately sold USB device Wired remote input Hard wired remote control adaptor can be connected sold separately 20 cm 7 7 8 in iPod Dock connector Interface cable 50 cm 20 in Left Right Front speaker Front speaker White Gray Gray black White black Green Violet Green black Violet black Green Violet Gree...

Page 3: ...eau avant Si vous ne prévoyez pas de détacher le panneau avant il peut être fixé avec la vis fournie Connexions des appareils Français Note Si cet appareil est installé dans un véhicule sans position ACC accessoire sur le commutateur d allumage le câble rouge doit être connecté à une borne qui peut détecter la position du commuta teur d allumage Sinon la batterie risque de se décharger ACC O N S T...

Page 4: ...orisée max 300 mA 12 V CC Caisson de grave Caisson de grave Enceinte arrière Enceinte arrière Enceinte avant Enceinte avant Lecteur de CD à chargeur vendu séparément Orange blanc Raccordez ce fil à la borne du commutateur d éclairage Avec un système à deux enceintes ne raccordez rien aux fils d enceinte qui ne sont pas connectés aux enceintes Caisson de grave 4 Ω Caisson de grave 4 Ω Lors de l uti...

Reviews: