Pioneer DEH-6350SD, Owner'S Manual

Page: 9 / 100

This unit is equipped with a subwoofer output
which can be turned on or off.
1
Press M.C. to display the setting mode.
2
Turn M.C. to select the desired setting.
NORMAL (normal phase)
—
REVERSE (reverse
phase)
—
OFF
(subwoofer off)
3
Press M.C. to confirm the selection.
SW SETTING 2
(subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1
Press M.C. to display the setting mode.
2
Press M.C. to cycle between the cut-off fre-
quency and output level of the subwoofer.
3
Press M.C. to switch to cut-off frequency and
then turn M.C. to select the cut-off frequency.
50HZ
—
63HZ
—
80HZ
—
100HZ
—
125HZ
4
Press M.C. to switch to output level and then
turn
M.C.
to adjust the output level.
Adjustment range: +6 to -24
HPF SETTING
(high pass filter adjustment)
When you do not want low sounds from the sub-
woofer output frequency range to play from the
front or rear speakers, turn on the HPF (high pass
filter). Only frequencies higher than those in the
selected range are output from the front or rear
speakers.
1
Press
M.C.
to display the setting mode.
2
Turn M.C. to select the cut-off frequency.
OFF (off)
—
50HZ
—
63HZ
—
80HZ
—
100HZ
—
125HZ
3
Press M.C. to confirm the selection.
BASS BOOSTER (bass boost)
1
Press
M.C.
to display the setting mode.
2
Turn M.C. to adjust the level.
Adjustment range: 0 to +6
3
Press M.C. to confirm the selection.
SLA
(source level adjustment)
SLA (Source Level Adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
!
When selecting FM as the source, you cannot
switch to
SLA .
!
Settings are based on the FM volume level,
which remains unchanged.
!
The AM volume level can also be adjusted with
this function.
1
Press M.C. to display the setting mode.
2
Turn
M.C.
to adjust the source volume.
Adjustment range: +4 to
–
4
3
Press M.C. to confirm the selection.
Initial Settings
1 Press and hold SRC/OFF until the unit
turns off.
2 Press M.C. and hold until the initial set-
ting menu appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
CLOCK SET (setting the clock)
1
Press M.C. to display the setting mode.
2
Press M.C. to select the segment of the clock
display you wish to set.
Hour
—
Minute
3
Turn M.C. to adjust the clock.
FM STEP
(FM tuning step)
The FM tuning step employed by seek tuning can
be switched between 100 kHz, the preset step, and
50 kHz.
!
If seek tuning is performed in 50 kHz steps,
stations may be tuned in imprecisely. Tune in
the stations with manual tuning or use seek
tuning again.
!
The tuning step remains at 50 kHz during man-
ual tuning.
1
Press M.C. to display the setting mode.
2
Turn
M.C.
to select the FM tuning step.
100KHz (100 kHz)
—
50KHz (50 kHz)
3
Press M.C. to confirm the selection.
AM STEP (AM tuning step)
The AM tuning step can be switched between 9
kHz, the preset step, and 10 kHz. When using the
tuner in North, Central or South America, reset
the tuning step from 9 kHz (531 kHz to 1 602 kHz
allowable) to 10 kHz (530 kHz to 1 640 kHz allow-
able).
1
Press M.C. to display the setting mode.
2
Turn M.C. to select the AM tuning step.
9kHZ (9 kHz)
—
10kHZ (10 kHz)
3
Press M.C. to confirm the selection.
AUX (auxiliary input)
Activate this setting when using an auxiliary de-
vice connected to this unit.
1
Press M.C. to turn AUX on or off.
USB PNP (plug and play)
This setting allows you to switch your source to
USB / USB-iPod automatically.
1
Press M.C. to turn the plug and play function
on or off.
ON
–
When a USB storage device/iPod is con-
nected, depending on the type of device, the
source is automatically switched to
USB / USB-
iPod when you turn on the engine. If you dis-
connect your USB storage device/iPod, this
unit
’
s source is turned off.
OFF
–
When a USB storage device/iPod is con-
nected, the source is not switched to USB /
USB-iPod automatically. Please change the
source to USB / USB-iPod manually.
SW CONTROL (rear output and subwoofer set-
ting)
This unit
’
s rear output (rear speaker leads output)
can be used for full-range speaker ( FUL ) or sub-
woofer ( SW ) connection. If you switch the rear out-
put setting to
SW
, you can connect a rear speaker
lead directly to a subwoofer without using an aux-
iliary amp.
Initially,
REAR SP is set for rear full-range speaker
connection ( FUL ).
1
Press
M.C.
to display the setting mode.
2
Turn M.C. to change the output and press to
select.
REAR SP : FUL
—
SW
3
Press M.C. to confirm the selection.
DEMO (demo display setting)
1
Press M.C. to turn the demo display on or off.
EVER SCRL (scroll mode setting)
When ever scroll is set to ON, recorded text infor-
mation scrolls continuously in the display. Set to
OFF if you prefer the information to scroll just
once.
1
Press M.C. to turn the ever scroll on or off.
English
Operating this unit 02
9
Section
Operating this unit
En
<YRD5332-A/S>9