Pioneer AVH-X6800DVD, Owner'S Manual

Page: 7 / 204

7
 Refer to Checking part names and functions on page 8
Settings and recorded contents are reset to the factory settings.
About this manual
This manual uses diagrams of actual screens to describe opera-
tions. However, the screens on some units may not match those
shown in this manual depending on the model used.
Meanings of Symbols Used in This
Manual
X0000BT
This indicates model name that are supported
the described operations.
This indicates to touch an appropriate soft key
on the touch screen.
HOLD
This indicates to touch and hold an appropriate
soft key on the touch screen.
This indicates that there is a reference or
supplementary for the key or screen.
Protecting your unit from theft
The front panel can be detached to deter theft.
Important
 Handle the front panel with care when removing or
attaching it.
 Avoid subjecting the front panel to excessive shock.
 Keep the front panel out of direct sunlight and high
temperatures.
 If removed, replace the front panel on the unit before
starting up your vehicle.
 To avoid damaging the device or vehicle interior, remove
any cables and devices attached to the front panel before
detaching it.
Removing the front panel
1 Pinch the top and bottom of its right side and
pull the front panel out.
Take care not pinch it too tightly or to drop it, and also avoid
contact with water or other fluids to prevent permanent damage.
Re-attaching the front panel
1 Slide the front panel to the left.
The front panel and the head unit are connected on the left side.
Make sure that the front panel has been properly connected to
the head unit.
2 Press the right side of the front panel until it is
firmly seated.
If you can’t attach the front panel to the head unit successfully,
try again.
Forcing the front panel into place may result in damage.
Use and care of the remote
control
Installing the battery
Slide the tray on the back of the remote control out and insert the
battery with the plus (+) and minus (–) poles aligned properly.
 When using for the first time, pull out the film protruding
from the tray.
WARNING
 Do not ingest the battery, Chemical Burn Hazard.
 This product, including the supplied remote control,
contains a coin/button cell battery. If the coin/button cell
battery is swallowed, it can cause severe internal burns in
just two hours and can lead to death.
 Keep new or used batteries out of the reach of children.
If the battery is swallowed or placed inside any part of the
body, consult a doctor immediately.
 If the battery compartment does not close securely, stop
using the product and keep it away from children.
 Batteries (battery pack or batteries installed) must not be
exposed to excessive heat such as sunshine, fire or the
like.
CAUTION
 Remove the battery if the remote control is not used for a
month or longer.
 There is a danger of explosion if the battery is incorrectly
replaced. Replace only with the same or equivalent type.
 Do not handle the battery with metallic tools.
 Do not store the battery with metallic objects.

If the battery leaks, wipe the remote control completely
clean and install a new battery.

When disposing of used batteries, comply with
governmental regulations or environmental public
institutions’ rules that apply in your country/area.
 “Perchlorate Material – special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. (Applicable
to California, U.S.A.)”
Using the remote control
Point the remote control in the direction of the front panel to
operate.
 The remote control may not function properly in direct
sunlight.
Protecting the LCD panel and
screen

Do not expose the LCD screen to direct sunlight when this
product is not used. This may result in LCD screen malfunc-
tion due to the resulting high temperatures.
 When using a cellular phone, keep the antenna of the cel-
lular phone away from the LCD screen to prevent disruption
of the video in the form of spots, colored stripes, etc.

To protect the LCD screen from damage, be sure to touch the
touch panel keys only with your finger and do so gently.
Notes on internal memory
Before removing the vehicle battery
 Some of the settings and recorded contents will not be reset.
Data subject to erasure
The information is erased by disconnecting the yellow lead from
the battery (or removing the battery itself).
 Some of the settings and recorded contents will not be reset.
Resetting the microprocessor
CAUTION
Pressing the RESET button resets settings and recorded
contents to the factory settings.
 Do not perform this operation when a device is connected
to this product.
 Some of the settings and recorded contents will not be
reset.
The microprocessor must be reset under the following
conditions:
 Prior to using this product for the first time after installation.
 If this product fails to operate properly.
 If there appears to be problems with the operation of the
system.
 If your vehicle position is shown on the map with a signifi-
cant positioning error.
1 Turn the ignition switch OFF.
2 Press the
RESET button with a pen tip or other
pointed implement.
7 < CRD4918-A >
Precaution Precaution