Pioneer avh-4200nex, Owner'S Manual

Page: 66 / 244

66
The audio or video skips.
 This product is not firmly secured.
— Secure this product firmly.
No sounds are produced. The volume level will not rise.
 Cables are not connected correctly.
— Connect the cables correctly.
 The system is performing still, slow motion, or frame-by-
frame playback with DVD-Video.
— There is no sound during still, slow motion, or frame-by-
frame playback with DVD-Video.
 The system is paused or performing fast reverse or forward
during the disc playback.
— For the media other than music CD (CD-DA), there is no
sound on fast reverse or forward.
The icon  is displayed, and operation is impossible.
 The operation is not compatible with the video configuration.
— The operation is not possible. (For example, the DVD
playing does not feature that angle, audio system, subtitle
language, etc.)
The picture stops (pauses) and this product cannot be
operated.

The reading of data is impossible during disc playback.
— Stop playback once, then restart.
The picture is stretched, with an incorrect aspect ratio.
 The aspect setting is incorrect for the display.
— Select the appropriate setting for that image.
A parental lock message is displayed and DVD playback
is not possible.
 The parental lock is on.
— Turn the parental lock off or change the level.
The parental lock for DVD playback cannot be canceled.
 The code number is incorrect.
— Input the correct code number.
The DVD video is not played back with the audio/subtitle
language specified in “
DVD/DivX Setup ”.
 The DVD does not support the language selected in “ DVD/
DivX Setup ”.
— Playback in the selected language is not possible if the
language selected in “ DVD/DivX Setup ” is not recorded
on the disc.
Install the microphone on the sun visor when it is in the up
position. It cannot recognize the driver’s voice if the sun visor is
in the down position.
Installation on the steering
column
1 Detach the microphone base from the micro-
phone clip by sliding the microphone base
while pressing the tab.
4
1
2
3
1 Microphone
2
Tab
3 Microphone base
4
Microphone clip
2 Mount the microphone on the steering column.
2
1
1
Double-sided tape
Install the microphone on the steering column, keeping it
away from the steering wheel.
2
Clamps
Use separately sold clamps to secure the lead where neces-
sary inside the vehicle.
Adjusting the microphone
angle
The microphone angle can be adjusted.
Troubleshooting
If you have problems operating this product, refer to this sec-
tion. The most common problems are listed below, along with
likely causes and solutions. If a solution to your problem cannot
be found here, contact your dealer or the nearest authorized
Pioneer service facility.
Common problems
A black screen is displayed, and operation is not possible
using the touch panel keys.
 “ Power OFF ” mode is on.
— Press any button on this product to release the mode.
 The rear view camera image is displayed with no camera
connection and the wrong camera polarity setting.
— Press and hold the MUTE button to release the rear view
camera screen and then change the camera polarity set-
ting to “ Battery ”.
Problems with the AV screen
CD or DVD playback is not possible.
 The disc is inserted upside down.
— Insert the disc with the label upward.
 The disc is dirty.
— Clean the disc.
 The disc is cracked or otherwise damaged.
— Insert a normal, round disc.
 The files on the disc are in an irregular file format.
— Check the file format.
 The disc format cannot be played back.
— Replace the disc.
 The loaded disc is a type this product cannot play.
— Check what type of disc it is.
The screen is covered by a caution message and the video
cannot be shown.
 The parking brake lead is not connected or the parking brake
is not applied.
— Connect the parking brake lead correctly, and apply the
parking brake.
 The parking brake interlock is activated.
— Park your vehicle in a safe place and apply the parking
brake.
No video output from the connected equipment.
 The “ AV Input ” or “ AUX Input ” setting is incorrect.
— Correct the settings.
Appendix
66 < CRD4943-A > < CRD4943-A >
Installation Appendix Appendix