PIONEER DJ SERATO DDJ-REV7 Instruction Manual Download

Page: 70 / 118

Audio output

10.

Master level indicator

Displays the volume level of the master sound output to the [

MASTER 1

] and [

MASTER

] terminals.

Outputting sound

Adjusting the channel input volume

1 Slide the input selector switch to select an input sound

source.

2 Turn the [TRIM] knob to adjust the volume for the input sound.

The channel level indicator lights up when sound is input to the channel.

Adjusting the channel output volume

1 Move the channel fader to adjust the volume for the output

sound.

2 Move the crossfader to adjust the volume balance of the two

channels.

•

Press the [

SILENT CUE

] button to mute the sound of the track playing on the deck. Press

the button again to cancel the mute.
You can also cancel the mute by playing a Hot Cue.

Summary of Contents for SERATO DDJ-REV7























































































































Search results

Summary of Contents for SERATO DDJ-REV7

Reviews:

Related manuals for SERATO DDJ-REV7

Brands by name

Popular brands

PIONEER DJ SERATO DDJ-REV7, Instruction Manual

Search results

Summary of Contents for SERATO DDJ-REV7

Reviews:

Related manuals for SERATO DDJ-REV7

Brands by name

Popular brands