PIONEER DJ SERATO DDJ-REV7 Instruction Manual Download | Manualshive

Page: 21 / 118

background image

21

PC/Mac setup

To input or output your PC/Mac’s audio to/from the unit, install the dedicated audio driver
software and/or Setting Utility on your computer.
If you install the audio driver software to your PC (Windows), Setting Utility will also be
installed with the driver software.
If you use a Mac, install Setting Utility only.

•

For information on the latest system requirements, compatibility, and supported operating
systems, visit the URL below.

pioneerdj.com/support/

•

Operation isn’t guaranteed on all PC/Mac models, even if the system requirements are
met.

•

Operation isn’t guaranteed when multiple units are connected to a PC/Mac.

•

If a PC (Windows) without the dedicated audio driver software installed is connected to the
unit, errors may occur on the PC.

•

Malfunctions may occur due to incompatibility with other software installed on a PC/Mac.

Installation



Notes on installation

•

Turn the unit off and disconnect the USB cable connected to the unit and the PC/Mac
before installation.

•

Close all applications running on the PC (Windows) before installation.

•

You’ll need admin rights to install the dedicated audio driver software to your PC
(Windows).

•

Read the License Agreement terms carefully before installation.

•

If you quit the installation halfway through, perform the installation procedure from the
beginning again.

•

After the installation is complete, connect the PC/Mac to the unit.

•

Operation isn’t guaranteed on all PC/Mac models.

«
...
19
20
21
22
23
...
»

Summary of Contents for SERATO DDJ-REV7























































































































Reviews:

No comments

Related manuals for SERATO DDJ-REV7

Brand: NARGESA Pages: 33

Brand: Makita Pages: 8

Brand: VECTECH Pages: 5

Brand: JB Systems Pages: 12

Brand: RayLight Pages: 34

GAZELLE FREESTYLE

Brand: Gazelle Pages: 10

Brand: Latham Pages: 19

Lab companion SI-300

Brand: Jeio tech Pages: 69

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 4

Brand: Jct Pages: 16

Brand: B. Braun Pages: 40

Brand: B. Braun Pages: 4

Brand: Toro Pages: 4

Evo TM/TSV2 Awning Wall Set

Brand: Zempire Pages: 2

Brand: GERATHERM Pages: 40

Brand: Stanton Pages: 13

MobilGate - 128c

Brand: SeaSoft Pages: 11

Brand: Emos Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands