Pilz 632020 Operating Manual Download Page 44

Page: 44 / 67

PSEN opII3H Series

Operating Manual PSEN opII3H Series
1003503-EN-05

| 44

Transmitter

Status

Safety light curtain in operation

Transmitter sends uncoded

green

Safety light curtain in operation

Transmitter sends A-coded

green

Safety light curtain in operation

Transmitter sends B-coded

green

Check whether the coding corresponds to the specifications in

Installation of several adja-

cent safety light curtains [

22]

Check the

pin assignment [

33]

, when other displays can be seen at the safety light cur-

tain.

Interrupt the protected field. The following LED must light at the receiver:

Meaning

green

red

green

Protected field is interrupted,

A-coded

green

red

green

Protected field is interrupted,

B-coded

Check after plant/machine modification

Check the safety light curtain each time the plant/machine is modified.

The following measures should also be regarded as a modification:

}

The exchange of the safety light curtain

}

The exchange of components of the safety light curtain

}

A changed connection of the safety light curtain (change from uncoded connection to
coded connection).

You

must

comply with the requirements of the applicable national regulations.

INFORMATION

This inspection may only be carried out by qualified personnel.

The Appendix contains a

Checklist [

64]

which should help you perform the safety

check.

Summary of Contents for 632020




































































Search results

Summary of Contents for 632020

Reviews:

Related manuals for 632020

Brands by name

Popular brands

Pilz 632020, Operating Manual

Search results

Summary of Contents for 632020

Reviews:

Related manuals for 632020

Brands by name

Popular brands