Assembly Guide
– SGSP – Senior Portable Soccer Goals
If you need assistance during installation phone us on 13 PILA (13 7452)
P 13 PILA (13 7452) E
W
www.pilasport.com.au
ABN 32 114 687 820
IMPORTANT
The information contained in this document is general advice only and is not engineers advice or certification. PILA group does not
warrant the accuracy of this information and will not be held liable for its content or outcomes. It is the user’s responsibility to check that this
information is suitable for their needs. Seek advice from your engineer if required. This document is confidential and is not to be redistributed.
Copyright ©2002-2014 PILA group® Pty Ltd. All rights reserved. Registered Trademark.
Note: This is a 2-person assembly. The product must be assembled correctly and maintained on a regular basis by
checking all joints, bolts, screws, clips and nets. Failure to do so may void the warranty.
Lay out all components in the shape of the goal. Per end there will be 2 x uprights (part#3), 2 x sections to make the crossbar
(part#1), elbows (part#4) and crossbar adapter fitted into the crossbar (part#2).
Connect the 2 sections of the crossbar (part#1) using the adapter (part#2) which will be already pre-connected to one of the
sections. Make sure each crossbar section is matched up with corresponding section (all sections are numbered). Connect the
other side of the crossbar join using 2 x M8 x 90mm s/s allen key bolts and 2 x M8 x 20mm s/s counter sunk star torx barrel nuts
(part#13). Tighten both bolts firmly using keys supplied.
Insert into the upright posts net track (part#3) 2 large alloy hex nuts (part#14) and leave them on the upper end of post towards
the elbow. These hold the bottom of the D net support (part#5) and the top of the rear support bar (part#7).
Connect the D net supports (part#7) to the lug on the elbows (part#4) using the M8 x 60mm gal hex bolts with flat and spring
washers (part#16). The bottom side of each D net support (part#5) must be connected to the large alloy hex nut (part#14)
previously inserted on the upright post (part#3) by using the M8 x 16mm s/s hex head bolt with flat and spring washers(part#15).
Connect the D bracing bar (part #6) to the D net support (part#5) and crossbar (part #1) by using 1 x M8 x 60mm gal hex head
bolt with washers and nuts (part #16) (to fix D net support (part #4)) and 1 x M8 x 16mm s/s hex head bolt and washers (part
#15) (to fix crossbar (part #1)). The large alloy nut (part#14) is already installed in the crossbar net track (part #1).
Assemble the back base bar (part#9) (net track side facing up) by connecting the 2 rear base elements using the back base
steel connecting bar (part#10). Loosen the 4 x M8 x 16mm s/s hex head bolt and washers (part#15) on both back base bars
(part#9). Pull out steel connecting bar (part#10) to black line on the bar. This is the centre point. Tighten 2 of x M8 x 16mm s/s
hex head bolt and washers (part#15) making sure they go through the back base bar to secure firmly in place. Slide other side
of the back base bar (part#9) over the steel connecting bar (part#10) and secure the bolts firmly.
Connect the back base bar (part #9) to the inside of the side base bars (part #8) using 2 flat alloy fixing plate 1 on top and 1 on
the bottom (part #12) and bolted using 4 x M8 x 90mm gal through bolts and washers on each corner (part #22).
Insert 3 large alloy hex nuts (part#14) into the net track side bars (part#8) (1 in the middle and 2 at the front). Attach the gal
fixing plate (part #11) to the front side of the side base bar (part #8) using 2 x M8 x 16mm s/s hex head bolts and washers
(part#15) into the large alloy hex nuts (part #14) already in net track. The gal fixing plate (part #11) should be in line with the
front edge of the side base bar (part #8). Add a 3rd large alloy hex nut (part #14) to the vertical hole on the gal fixing plate (part
#11) by using 1 x M8 x 16mm s/s hex head bolt and washers (part #15). Keep this bolt very loose so it can slide easily inside the
net track of the upright post (part #3) of the main goal frame.
Connect the rear support bar (part #7) to the side base bar (part #8) by using 1 x M8 x 16mm s/s hex head bolt and washers
(part #15) into the large alloy hex nut (part #14) already inserted into side base bar (part #8). The rear support bar (part #7) will
hold itself on a 45 degree angle with the 1 bolt fitting.
2 people can now lift the completed base frame 90 degrees to a vertical position (1 person at each side base bar) and carefully
slide the large alloy nut (part #14) attached to the gal fixing plate (part #11) into the net track at the bottom of the upright post
(part #3) of the main goal frame. Slide the side base frame into the net track until the bottom of the side base (part#8) frame is
flush with the bottom of the upright post (part #3) of the main goal. Tighten the M8 x 16mm s/s hex head bolt (part #15) to hold
in position.
Fix the other end of the rear support bar (part #7) to the upright post (part #3) of the main goal frame using the M8 x 16mm s/s
hex head bolt (part #15) into the large alloy hex nut (part #14) already inserted into the upright post (part #3) of main goal frame.
