pigtronix INFINITY 2 User Manual Download Page 6 | Manualshive

Page: 6 / 13

pigtronix INFINITY 2 User Manual Download Page 6

6

OFF = no audio recorded
RED = Recording
GREEN = Playback
ORANGE = Overdubbing
Blinking RED = Recording will start at loop boundary
Blinking GREEN = Playback will start at loop boundary
Blinking ORANGE = Overdub will start at loop boundary
Slow Blinking GREEN = Loop is stopped, audio is present

LED COLORS

This knob controls the volume of loop audio only. Unity gain is located at 12:00.

For typical looper performance, keep the DECAY knob set fully clockwise.
This knob controls the rate of loop decay during overdub.
With the Decay knob set fully clockwise, overdubs pile up at full volume. With the Decay knob set

fully counter-clockwise, each overdub lasts for only one loop cycle.
With the Decay knob set anywhere between those extremes, overdubbing on the Infinity 2 creates

constantly evolving loop textures that can be instantly snapped back to a previous state using the

Undo function.

The soft-touch MODE switch located above the Loop 2 footswitch allows the Loop 2 footswitch to

be reassigned to perform alternate functions.
Pressing the MODE switch repeatedly will cycle through STOP, ONCE and OCTAVE functions before

returning to Loop 2 control.
Pressing and holding the MODE switch will turn on the UNDO/REDO mode.
Note: Turning UNDO/REDO mode on and off will clear all current loop audio.

VOLUME KNOB

DECAY KNOB

SOFT-TOUCH MODE SWITCH

«
...
4
5
6
7
8
...
»

Summary of Contents for INFINITY 2














Reviews:

No comments