pico Technology PicoSource PG900 Series User Manual Download | Manualshive

Page: 8 / 56

background image

Introduction

4

Copyright © 2016 Pico Technology. All rights reserved.

pg900ug.en r1

1.3.2

Maximum input/output ranges

Observe all terminal ratings and warnings marked on the product.

The table below indicates the maximum voltage of the outputs and the overvoltage
protection range for the trigger input on each pulse generator. The overvoltage
protection ranges are the maximum voltages that can be applied without damaging
the instrument.

Connection port

Maximum voltage

(output or input)

Overvoltage protection

Integrated pulse outputs

±8 V unterminated

±10 V

Do not connect a source

Drive outputs

±5 V DC or AC pk

±5 V DC or AC pk

Do not connect a source

Tunnel diode pulse head

outputs

250 mV

0 V

Do not connect a source

Trigger input

±2 V DC or AC pk

±2 V DC or AC pk

Trigger output

+3 V DC or AC pk

+4 V / –2 V DC

Do not connect a source

WARNING

To prevent electric shock, do not connect an input voltage to the integrated
pulse outputs or the tunnel diode pulse heads.

CAUTION

Exceeding the overvoltage protection range on any connector can cause
permanent damage to the instrument and other connected equipment.

CAUTION

To prevent permanent damage, do not apply an input voltage to any of the
output channels of the pulse generator.

1.3.3

Grounding

WARNING

The instrument's ground connection through the USB cable is for functional
purposes only. The instrument does not have a protective safety ground.

WARNING

To prevent injury or death, never connect the ground of an input or output
(chassis) to any electrical power source. To prevent personal injury or death,
use a voltmeter to check that there is no significant AC or DC voltage
between the pulse generator's ground and the point to which you intend to
connect it.

CAUTION

Applying a voltage to the ground input is likely to cause permanent damage
to the instrument, the attached computer, and other equipment.

CAUTION

To prevent signal degradation caused by poor grounding, always use the
high-quality USB cable supplied with the instrument.

«
...
6
7
8
9
10
...
»

Summary of Contents for PicoSource PG900 Series

























































Reviews:

No comments

Related manuals for PicoSource PG900 Series

EF3000iSE - Inverter Generator - 3000 Maximum AC...

Brand: Yamaha Pages: 327

Brand: Rockpals Pages: 16

Brand: Thurlby Thandar Instruments Pages: 111

Brand: L&R Pages: 10

Brand: Black Diamond Equipment Pages: 12

Brand: MQ Power Pages: 42

Brand: PRETUL Pages: 28

Brand: Chicago Electric Pages: 25

Redi-Line DA12A

Brand: Pacific Scientific Pages: 97

Brand: EENOUR Pages: 36

Brand: Skyworks Pages: 74

Brand: Fabco Power Pages: 12

Brand: Intelligent Energy Pages: 14

Brand: Abbott Pages: 28

Brand: Neptune Systems Pages: 13

Brand: DC GENERATORS Pages: 7

Brand: GE Pages: 128

SuperBase V6400

Brand: Zendure Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands