pico Technology PicoSource PG900 Series User Manual Download | Manualshive

Page: 47 / 56

background image

PicoSource PG900 Series User's Guide

43

Copyright © 2016 Pico Technology. All rights reserved.

pg900ug.en r1

6

Specifications and characteristics

The distinction between specifications, characteristics, typical performance, and
nominal values is as follows.

Specifications

describe guaranteed performance over the temperature range +15ºC

to +25ºC (unless otherwise noted). All specifications apply after the instrument’s
temperature has been stabilized after 1 hour of continuous operation. Unless otherwise
noted, corrected limits are given when specifications are achieved using software
processing.

Many performance parameters are enhanced through frequent, simple calibrations.

All specifications are subject to change without notice. Specifications are valid after a 1
hour warm-up period, and ±5°C from the firmware calibration temperature.

Characteristics

provide useful, but not guaranteed, information about the functions

and performance of the instrument.

Typical Performance

, where listed, is not guaranteed, but indicates the performance

that most units will exhibit.

Nominal Value

indicates the expected, but not guaranteed, value of the parameter.

Factory Calibration Cycle.

For optimum performance, the instrument should have a

complete verification of specifications once every 12 months.

6.1

PG900 family specifications

Specifications

PicoSource PG911

PicoSource PG912

PicoSource PG914

Generation
technique

Integrated step

recovery diode pulse

outputs

Drive outputs with
tunnel diode pulse

heads

Integrated step

recovery diode pulse

outputs and

drive outputs with

tunnel diode pulse

heads

Output
channels

2 SRD

2 TD

2 SRD + 2 TD

Output
waveform

Dual-channel positive

and negative pulse

generators with

controlled amplitude

and timing

parameters

Dual-channel positive

and negative pulse

generators with fixed

amplitude and

controlled timing

parameters

Four-channel positive

and negative pulse

generators with

controlled amplitude

and timing

parameters

«
...
45
46
47
48
49
...
»

Summary of Contents for PicoSource PG900 Series

























































Reviews:

No comments

Related manuals for PicoSource PG900 Series

Brand: MIOX Pages: 82

Brand: SIGLENT Pages: 38

Brand: DUROMAX Pages: 82

Brand: DUROMAX Pages: 84

Brand: Snap-On Pages: 21

Brand: Wagan Pages: 7

Brand: Jegs Pages: 25

Brand: UNI-T Pages: 44

Brand: Tabor Electronics Pages: 298

Brand: EINHELL Pages: 24

Brand: ABB Pages: 46

Brand: FAST ComTec Pages: 11

Brand: Navigator Pages: 30

Brand: ACD Pages: 52

Brand: unicraft Pages: 46

Brand: unicraft Pages: 66

mr. steam MS90E

Brand: Feel Good Pages: 25

Brand: 365SMART Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands