PI P-843 User Manual Download Page 24 | Manualshive

Page: 24 / 34

background image

8

Maintenance

The P-843 is maintenance-free.

8.1

Cleaning

Requirements

✓

You have disconnected the P-843 from the electronics.

✓

The P-843 is

discharged (p. 22)

Auxiliary Materials Required

■

Soft, lint-free cloth

■

Mild cleaning agent or disinfectant

If you have any questions on the auxiliary materials recommended for the P-843, contact our

customer service department (p. 27)

NOTICE

Short-circuiting due to cleaning fluid penetrating the housing!

Cleaning fluid penetrating the P-843’s housing can short-circuit the actuator and drive
electronics.

►

Disconnect the P-843 from the electronics before cleaning.

►

Prevent cleaning fluid from penetrating the P-843‘s housing.

NOTICE

Damage due to unsuitable cleaning agents!

Some cleaning agents may cause damage to the P-843.

►

Use mild cleaning agents or disinfectants only.

NOTICE

Damage from ultrasonic cleaning!

Ultrasonic cleaning can damage the P-843.

►

Do not do any ultrasonic cleaning.

Cleaning the P-843

1. Dampen the cloth with the cleaning agent or disinfectant.
2. Carefully wipe the surfaces of the P-843.

8 MAINTENANCE

P843M0001EN

‒

2/23/2021

24

M O T I O N | P O S I T I O N I N G

«
...
22
23
24
25
26
...
»

Summary of Contents for P-843



































Reviews:

No comments

Related manuals for P-843

Brand: Eaton Pages: 86

Brand: YASKAWA Pages: 256

Brand: Quectel Pages: 23

Brand: Quectel Pages: 79

Brand: Campbell Pages: 3

Brand: Gardena Pages: 14

Brand: Gardena Pages: 8

Brand: Hanna Instruments Pages: 54

Brand: Hanna Instruments Pages: 2

Brand: Valcom Pages: 6

Brand: Watts Pages: 17

Brand: FUTABA Pages: 8

Brand: WAGNER Pages: 128

Brand: Climatisation Pages: 52

Brand: TECOM Pages: 8

Brand: IDEATEC Pages: 32

Brand: Broadcast Tools Pages: 15

NuMicro M252 Series

Brand: Nuvoton Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands