PI L-738 Series User Manual Download Page 39

Page: 39 / 55

10 Technical Data

L-738 / V-738 Precision XY Stage

MP183E

Version: 1.1.2

10.1

Specifications

The specified data applies to a temperature of

20 °C

(±3 °C) and

horizontal

installation.

10.1.1

Data Table

L 738.051100 / L 738.051111 / L 738.051112

L 738.051100

L 738.051111

L 738.051112

Unit

Tolerance

Motion and positioning

Active axes

X, Y

Travel range

102 × 102

Integrated sensor

–

Incremental linear

encoder with

sin/cos signal

transmission

Incremental linear

encoder with A/B

quadrature signal

transmission

Design resolution

0.001

0.01

µm

Sensor signal period

–

µm

Minimum incremental motion 0.2

0.05

µm

typ.

Unidirectional repeatability

0.2

0.05

µm

typ.

Bidirectional repeatability

±2

±0.5

µm

typ.

Reference point switch

repeatability

µm

typ.

Angular error xry (pitch)

±40

µrad

typ.

Angular error xrz (yaw)

±20

µrad

typ.

Angular error yrx (pitch)

±40

µrad

typ.

Angular error yrz (yaw)

±20

µrad

typ.

Straightness / flatness

±2

µm

typ.

Orthogonality

±96.963

µrad

typ.

Velocity

mm/s max.

Reference and limit switches

optical

Technical Data

Summary of Contents for L-738 Series
























































Search results

Summary of Contents for L-738 Series

Reviews:

Brands by name

Popular brands

PI L-738 Series, User Manual

Search results

Summary of Contents for L-738 Series

Reviews:

Brands by name

Popular brands