10
www.phywe.com, © All rights reserved
12620-09 and 12620-10 / 2715
After an unsuccessful calibration, the values can be reset to
the factory settings by way of "Reset" (4.3). An "attention"
symbol will be displayed requiring the user to confirm the
entry.
Note:
If the Cobra4 Sensor-Unit Condu (12632-00) is
used, the menu item under 4.3 is the item
Cell constant.
Here, the cell constant of the conductivity sensor that is used
can be entered and saved.
5.4.7
Setup/Date/Time (5.1)
The date and time can be selected by way of the navigation
keys
▲▼ and they can be adjusted with ◄►.
5.4.8
Setup/Battery status (5.2)
The current consumption of the activated Cobra4 Mobile-
Links leads to a continuous decrease of the supply voltage.
This menu can be used to enquire the battery status. In addi-
tion, the total capacity of the battery, the charging time, and
the remaining capacity are displayed (Fig. 24).
If the capacity of the battery falls below a critical threshold
(10
% of the remaining battery capacity) the battery symbol
will be displayed in red in the header of the display. Prior to
the automatic shut-down of the device, any running meas-
urements will be stored automatically.
5.4.9
Setup/Device (5. 3)
Selection of the device properties by way of the arrow
keys
▼▲ and confirmation by way of the confirmation key
.
The following settings can be realised by way of ◄►:
-
Language of the device menu. You can choose between
German
, English
, and Russian
.
-
Sound: The sound of the keystrokes of the device can be
switched on
or off
.
-
GPS: (option) In order to localise the device, a satellite
connection can be set up. This function is switched off as
standard. After it has been switched on by way of the
switch, the GPS symbol
will be displayed in the
header.
-
The automatic rotation of the device display can be
switched on
and off
.
Use the confirmation key
in order to confirm a new setting.
5.4.10
Setup/Information (5.4)
Here, you can find general information concerning your de-
vice, e.g. the number of the firmware version, the number of
devices, and the last update of the Mobile-Link.
5.4.11
Setup/Large Display (5.5)
Here, the settings options for communication with up to two
large-scale display units (07152-93) can be selected if a
Display-Connect (12623-00) is attached.
The uppermost channel of the measurement display will be
transferred automatically to the first large-scale display unit. If
a second large-scale display unit is connected, the second
measuring channel that is to be displayed can be selected for
five radio channels.
5.4.12
Utilities/Stopwatch (6.1)
This feature enables you to record a time interval in the range
of a hundredth of a second.
After the start of the measurement with
, it is possible to
pause the measurement with ► and to resume it afterwards.
For every pause, one measurement value will be saved to a
list. Up to three measuring points can be displayed simulta-
neously. Then, the first one will be overwritten. Pressing
again stops the measurement and reset the stopwatch to
00:00:00.
Pressing
► while there is no running measurement will de-
lete all of the measurement values.
The various activities are visualised in the footer of the dis-
play.
Fig. 25: Display of the "Stopwatch" utility of the Cobra4 Mo-
bile-Link 2 after the second measurement
Fig. 24: Display of the submenu "Battery status" for the Co-
bra4 Mobile-Link 2
The setup data will be maintained in a bat-
tery-buffered manner for up to 8 years. How-
ever, this requires regular recharging of the
built-in battery.
Battery status
Menu
Stopwatch
10:20:67
00:01:38
10:20:67
00:00:00
Start
Capacity
1905 mAh
Remaining
1543
mAh
Rem. Time
191
min
81 %
Start
Menu > Setup
