Phytec phyCORE-TriCore Hardware Manual Download Page 47

Page: 47 / 53

phyCORE-TriCore Development Board

PHYTEC Meßtechnik GmbH 2009 L-730e_0

1.3.15

USB connector X12

Depending on the used phyCORE-module on the Development Board,
the USB connector X12 provides the following connection.

For the phyCORE-TC1130:

X12 enables the connection to the
TC1130 USB feature

For the phyCORE-TC1130 the following jumper settings are required:

Jumper Setting

Description

JP9

Open

Disconnect 5V from USB Bus

JP28

2+3

Table 26:

Jumper Configuration for X12 USB connector for

phyCORE-TC1130

For the phyCORE-TC1796:

X12 enables the connection to the
TC1796 onboard USB to UART
Bridge.

For the phyCORE-TC1796 the following jumper settings are required:

Jumper Setting

Description

JP9

Closed

configuration for phyCORE-TC1796 module

JP28

open

configuration for phyCORE-TC1796 module

Table 27:

Jumper Configuration for X12 USB connector for

phyCORE-TC1796

Caution:

USB to UART Bridge can not be used with the standard phyCORE
TC1796 module, due to the module HW-configuration.

Summary of Contents for phyCORE-TriCore






















































Search results

Summary of Contents for phyCORE-TriCore

Reviews:

Related manuals for phyCORE-TriCore

Brands by name

Popular brands

Phytec phyCORE-TriCore, Hardware Manual

Search results

Summary of Contents for phyCORE-TriCore

Reviews:

Related manuals for phyCORE-TriCore

Brands by name

Popular brands