background image

08/2020 

Compliance with Standards 

PhoXi 3D Scanners conforms with the following standards and test specifications. The test criteria under which 
were PhoXi 3D Scanners certified are stated in the standards. Please note that the certification status may 

change without notification. Consult your local Photoneo representative if you need additional information 

related to the latest listing of exact approvals. 

Declaration of Conformity 

With Directive 2001/95/EC on General Product Safety and Directive 2014/30/EU on Electromagnetic 
Compatibility 

Manufacturer: 

Business name

Photoneo s.r.o. 

Registered seat:

Jamnického 3, Bratislava 841 05, Slovak Republic 

Identification number:

47353309 

Tax ID:

2023884907 

EU VAT ID:

SK2023884907 

Contact:

[email protected]

, +421 948 766 598 

Product​

 (subject of Declaration): 

Photoneo® PhoXi® 3D Scanner  

Following the development and testing of the Product throughout 2015 up until now, hereby the Manufacturer 
declares that his Product complies with the requirements and limitations as stated in the Directive 2001/95/EC 

on General Product Safety and in the Directive 2014/30/EU on Electromagnetic Compatibility. 

The Declaration of Conformity is issued under the sole responsibility of the Manufacturer. It relies on testing 
provided by: 

Research Institute of Posts and Telecommunications, Testing and Metrology Division - Test Report 
22/602/2020/Eng 

Lasermet Limited (Bournemouth UK), Laser Classification Reports to EN 60825-1:2014 - No. 1830, 1997b 

and 1962 

Technical Testing Institute in Piestany / Technický skúšobný ústav Piešťany (dedicated Product 

Certification Body) - Conformity Certificate No. 181299001 

Rhein Tech Laboratories, Inc. - FCC Class B DoC Report No. 2017262DOC 

[email protected]

PhoXi 3D Scanner - User Manual and Installation Instructions

31/40 

Summary of Contents for PhoXi L









































Reviews: