Phoenix Advanced pressure monitor II Installation Manual Download | Manualshive

Page: 27 / 46

background image

APM2 Central Display Rough-In Installation

Wiring

23

MKT-0262 MPC-1748 Rev 02/13

APM2 Rough-In Installation Guide

3.4.2 Completing the Finish Wiring

1. Connect all the electrical connectors matching the wiring connector with the mates on the back of the

unit. Connectors are color coded and keyed.

2. Mount the unit cover to the electrical box using four of the supplied mounting screws. Leaving screws

slightly loose adjust the cover so that it is square. Securely tighten so that the back of the cover is tight to
the finish wall surface.

Figure 3-4.

Mounting APM2 Central Display in Triple Gang Electrical Box

3. Mount the front cover assembly.

Figure 3-5.

Installed APM2 Central Display

«
...
25
26
27
28
29
...
»

Summary of Contents for Advanced pressure monitor II















































Reviews:

No comments

Related manuals for Advanced pressure monitor II

ProLite XUB2893UHSU

Brand: Iiyama Pages: 31

Brand: Weldex Pages: 2

E-MOTIVE ATOM ATOM01-000-0-40-900

Brand: AVIRE Pages: 14

Brand: MIP Pages: 41

ProLite T1531SR

Brand: Iiyama Pages: 1

Brand: Environnement Pages: 196

Brand: Omron Pages: 36

e!DISPLAY 7300T

Brand: WAGO Pages: 104

Brand: Xerox Pages: 27

Brand: AOC Pages: 37

Sunlight Readable LCD Monitor

Brand: I-Tech Pages: 1

Brand: Eizo Pages: 76

Brand: Parker Pages: 45

Brand: AOC Pages: 67

Brand: OSEE Pages: 27

Brand: AOC Pages: 47

Brand: Polar Electro Pages: 25

Brand: Marshall Amplification Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands