manualshive.com logo in svg

Phoenix Contact RFC 4072S, User Manual, Page: 74 / 272

Share
Download
Phoenix Contact RFC 4072S User Manual Download Page 74

RFC 4072S

74 / 272

PHOENIX CONTACT

108580_en_02

Removing the SD card

•

Push the ejector downwards (B1). 

The SD card moves out of the slot (B2).

•

Remove the SD card.

Figure 3-4

Inserting (A) or removing (B) the SD card (parameterization memory)

Replacing the SD card

•

Remove the SD card to be exchanged according to the above description.

•

Then insert the replacement SD card.

3.6

Inserting/removing the USB memory stick

Procedure

A

B

B2

B1

NOTE: Potential RFC 4072S malfunction

A RFC 4072S malfunction can occur if the USB memory stick is inserted or removed while 

the RFC 4072S is supplied with power.

Only insert or remove the USB memory stick when the power supply of the RFC 4072S is 

switched off.

•

Switch off the supply voltage of the RFC 4072S.

•

Insert the USB memory stick into the USB socket of the RFC 4072S.

Or

Remove the USB memory stick from the USB socket of the RFC 4072S.

•

Switch on the supply voltage of the RFC 4072S.

Summary of Contents for RFC 4072S

















































































































































































































































































Reviews:

No comments