Phoenix Contact PLOTMARK User Manual Download Page 25

Page: 25 / 28

For your safety

107753_en_00

PHOENIX CONTACT

25 / 28

5.2

Technical data

Plotters

Plotter type

Flatbed plotter

Maximum plotter surface

422 mm x 305 mm

Plotter speed with marker pens

Up to 40 mm/s

Marker pens

Special marker pens with HP slot

Pen magazine

Up to four marker pens with double seal

Drive

2-phase step motor

Dimensions

690 mm x 480 mm x 155 mm

Weight

8.3 kg

Interface

USB level 2.0

Electronics

Command language

Control from CLIP PROJECT marking, command language

based on HP-GL 7475A

Mass storage

16 MB

Addressable resolution

0.025 mm

Repeat accuracy

0.05 mm

Power supply

Power supply

via external power supply unit with replaceable adapters

Power supply unit input voltage

100 VAC ... 240 V AC / 50 Hz ... 60 Hz

Power supply unit input current

Maximum 0.7 A

Power supply unit output voltage

24 V DC

Power supply unit output current

Maximum 1.25 A

Ambient conditions

Relative humidity

Operation

Storage

35% ... 75%

10% ... 90%

Ambient temperature

Operation

Storage

+10°C ... +35°C

-10°C ... +50°C

Summary of Contents for PLOTMARK





























Search results

Summary of Contents for PLOTMARK

Reviews:

Related manuals for PLOTMARK

Brands by name

Popular brands

Phoenix Contact PLOTMARK, User Manual

Search results

Summary of Contents for PLOTMARK

Reviews:

Related manuals for PLOTMARK

Brands by name

Popular brands