Phoenix Contact IOL MA8 PN DI8 User Manual Download

Page: 33 / 84

Web manager interface

4022_en_A

PHOENIX CONTACT

5.2.2

IO-Link configuration

When the IO-Link device is attached to a port, it begins operating without requiring any

configuration. The IOL MA8 PN DI8 and attached IO-Link device automatically negotiate the

“Minimum Cycle Time” value. If required by an application, set a specific “Minimum Cycle

Time” value.

This page provides special features such as Data Storage, Device Validation, and Data

Validation.

Editing the IOL MA8 PN DI8 port settings

If an IO-Link device is attached to the port, no configuration is required for operation. If a

digital input or output device is attached, it is necessary to change the Port Mode.

If necessary, open the IOL MA8 PN DI8 interface with the browser using the IP address.

Click the “Configuration” tab, and then click the “IO-LINK” subtab to access the “IO-

Link” page.

Figure 5-7

“IO-Link Settings” page

Summary of Contents for IOL MA8 PN DI8





















































































Search results

Summary of Contents for IOL MA8 PN DI8

Reviews:

Related manuals for IOL MA8 PN DI8

Brands by name

Popular brands

Phoenix Contact IOL MA8 PN DI8, User Manual

Search results

Summary of Contents for IOL MA8 PN DI8

Reviews:

Related manuals for IOL MA8 PN DI8

Brands by name

Popular brands