Phoenix Contact IOL MA8 PN DI8 User Manual Download

Page: 15 / 84

Configuration and startup

4022_en_A

PHOENIX CONTACT

Configuration and startup

4.1

Default settings

The default network settings of the IOL MA8 PN DI8 are:

IP address: 192.168.254.254

Subnet mask: 255.255.255.0

Gateway: 0.0.0.0

4.2

Web-based management

The user-friendly, web-based graphical user interface (GUI) allows management of the IOL

MA8 PN DI8 from anywhere in the network using a standard browser. Comprehensive

configuration and diagnostic functions, including a wide range of information about the

device itself, current parameters, and operating state, are clearly displayed.

Terminology for the GUI is shown below.

Figure 4-1

GUI terminology

The default settings are invoked whenever the system is reset.

Tab

Subtab

Page

Field

Group name

Summary of Contents for IOL MA8 PN DI8





















































































Search results

Summary of Contents for IOL MA8 PN DI8

Reviews:

Related manuals for IOL MA8 PN DI8

Brands by name

Popular brands

Phoenix Contact IOL MA8 PN DI8, User Manual

Search results

Summary of Contents for IOL MA8 PN DI8

Reviews:

Related manuals for IOL MA8 PN DI8

Brands by name

Popular brands