manualshive.com logo in svg

Phoenix Contact Axioline F, User Manual, Page: 81 / 86

Share
Download
Phoenix Contact Axioline F User Manual Download Page 81

Assembly and electrical installation

105739_en_04

PHOENIX CONTACT

81

D 2

Assembly and electrical installation

Checklist for assembly and electrical installation of the module

Device type/equipment identification

Version: HW/FW

Date

Editor

Test engineer 

Comment

No. Requirement (mandatory)

Yes

Comment

1

Was assembly completed according to the specifications 

(specifications from the planning phase or according to the user 

manual)?

2

Was the module installed in the control cabinet (IP54) and secured 

correctly?

3

Do the cable cross sections and installation correspond to the 

specifications?

4

Does the connection technology correspond to the specifications in the 

technical data and in the relevant user manual?

No. Requirement (optional)

Yes

No

Comment

5

Is the data width set correctly according to the specifications?

6

Is the profile/PROFIsafe address set correctly according to the 

specifications?

Date

Signature (editor)

Date

Signature (test engineer)

Summary of Contents for Axioline F























































































Reviews:

No comments