manualshive.com logo in svg

Phoenix Contact Axioline F, User Manual, Page: 27 / 86

Share
Download
Phoenix Contact Axioline F User Manual Download Page 27

Assembly, removal, and electrical installation

105739_en_04

PHOENIX CONTACT

27

4

Assembly, removal, and electrical installation

4.1

Assembly and removal

4.1.1

Unpacking the module

•

Read the packing slip and follow the instructions.

The module may only be installed and removed by qualified personnel. 

4.1.2

Preparation and assembly

•

Mount the module on a 35 mm DIN rail in a control cabinet or junction box protected 

from dust and humidity (IP54 or higher).

•

Secure the control cabinet/junction box to prevent unauthorized opening.

•

Only connect the cables using the supplied Axioline F connectors.

NOTE: Electrostatic discharge

The module contains components that can be damaged or destroyed by electrostatic 

discharge.

•

When handling the module, observe the safety precautions against electrostatic 

discharge (ESD) according to EN 61340-5-1 and IEC 61340-5-2.

WARNING: Unintentional machine startup

Make sure that the power to the system is disconnected before carrying out assembly and 

removal work as this could cause unintentional machine startup.

•

Before assembling or removing the module, disconnect the power to the module and 

the entire Axioline F station and make sure that the system cannot be switched on 

again.

•

Make sure the entire system is reassembled before switching the power back on and 

that neither the station nor the system poses a hazard.

Observe the diagnostics indicators and any diagnostic messages.

Summary of Contents for Axioline F























































































Reviews:

No comments