manualshive.com logo in svg

Phoenix Contact 2313669, User Manual, Page: 56 / 68

Share
Download
Phoenix Contact 2313669 User Manual Download Page 56

PSI-MODEMSHDSL/SERIAL

3-18

PHOENIX CONTACT

104275_en_c00

3.6

Firmware update

 

In order to benefit from a wider range of functions, you can download the latest firmware at 

www.phoenixcontact.net/catalog

 and transfer it to your device.

To update the firmware, you must switch to online mode.

NOTE: The device must not be disconnected from the PC or the power supply dur-

ing a firmware update as this can cause damage to the device.

Update firmware

Device informations

Type

The designation clearly identifies the type and function of the 

selected device. The designation is printed on the device.

Order No.

The order number can be used to clearly identify the device 

type. 

Serial No.

The serial number is unique for each device. It can be used to 

assign a device and is printed on the device.

Hardware version

The hardware version number clearly indicates the hardware 

version of the device. The two-digit number is printed on the 

device.

Firmware version

The firmware version number clearly indicates the firmware 

version of the device. The three-digit number is printed on the 

device.

Release date

The date the firmware was released.

Update firmware

Open firmware

Find and open firmware file (.bin) on data carrier.

Firmware file

Name of the open firmware file.

Firmware version

Firmware version of the update.

Release date

The date the firmware to be installed was released.

Start update

The selected firmware file is transferred to the device con-

nected via USB.

Summary of Contents for 2313669





































































Reviews:

No comments