Phoenix Contact 2313669 User Manual Download Page 18

Page: 18 / 68

PSI-MODEMSHDSL/SERIAL

1-12

PHOENIX CONTACT

104275_en_c00

1.6.4

Star structure via DIN rail connector and RS-485 interface

Figure 1-8

Star structure, RS-485

The devices are connected via the DIN rail connector (T-BUS) in the head station.

The DIN rail connector supports RS-485. It can not be used with RS-232 and RS-422.

In order to configure a star structure, you must create several line structures.

In the example, you need to create two line structures, each consisting of three devices.

Figure 1-9

Example for a star structure (RS-485 interface on all devices)

In principle, a star structure via the DIN rail connector can only be used in combination

with the RS-485 interface.

Make sure that

all devices connected via the DIN rail connector (T-BUS) use the

same serial data rates

SHDSL

...

RS 485

RS 485 RS 485 RS 485 RS 485

SHDSL

...

RS 485

RS 485 RS 485 RS 485 RS 485

SHDSL

Line 1

Line 2

Summary of Contents for 2313669





































































Search results

Summary of Contents for 2313669

Reviews:

Phoenix Contact 2313669, User Manual, Page: 18 / 68

Search results

Summary of Contents for 2313669

Reviews: